background image

1

Contents

July 22, 2004 Part 004840A Rev 01

Introduction............................................................................ 9

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
The Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
The Back Panel  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
The Internal Antenna  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Installing the SOMAport...................................................... 15

Unpack the SOMAport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Choose the Best Location  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Power on the SOMAport. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Connect Computer Using Ethernet. . . . . . . . . . . . . . . . . . . . . . . . . .19
Connect Computer Using USB. . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Connect Multiple Computers to the SOMAport  . . . . . . . . . . . . . . . .22
Connect Telephones to the SOMAport. . . . . . . . . . . . . . . . . . . . . . .23
Activate Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Troubleshooting .................................................................. 29

Finding Causes of Computer Problems . . . . . . . . . . . . . . . . . . . . . .30
Finding Causes of Telephone Problems  . . . . . . . . . . . . . . . . . . . . .31
The Signal is Weak. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
There is a Fault Condition  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
The SOMAport is Not Receiving Power . . . . . . . . . . . . . . . . . . . . . .34
There is a Problem with the Ethernet or USB Cabling . . . . . . . . . . .35
There is a Problem with the USB Port Settings . . . . . . . . . . . . . . . .37
The Computer Uses an Old Dial-Up Connection . . . . . . . . . . . . . . .38
Internet Explorer LAN Settings are Incorrect . . . . . . . . . . . . . . . . . .40
Ethernet Network Settings are Incorrect. . . . . . . . . . . . . . . . . . . . . .41
IP address Needs to be Renewed . . . . . . . . . . . . . . . . . . . . . . . . . .50

Specifications ..................................................................... 53

Index .................................................................................... 55

sp3.book  Page 1  Thursday, July 22, 2004  3:21 PM

Summary of Contents for SOMAport R3.0



























































Reviews: