background image

PRODUCT MANUAL 

8-Zone RGB Remote Control

8-Z
one R

GB R

emot

e C
on

tr

ol

 

 

Page 1

Product Description

Main Functions:

Solid Apollo’s 8 Zone color changing RGB-W remote control is fully wireless and can control up to 8 different light zones using just one

remote control. The SenseControl color wheel allows easy color selection, and can be fine tuned to an exact color using the single color

buttons. The controller works great with any LED products which use four channels, such as RGBW (red, green, blue and white). A wall

holder is also included for secure and easy storage.

•   Control up to 8 Recievers (1 Included) individually or as a group
•   Brightness levels can be controlled for each individual color/zone
•   Built in Color Changing Programs with chase effects
•   Memory Function remembers last setting if power goes out
•   On/Off switch of individual zones or all lights
•   Full Brightness Control
•   50 Foot Wireless Control   

This manual reviews:

Toll Free: 866.592.3873

Email: [email protected]

www.SolidApollo.com

•   Entire installation process
•   Product features and primary uses
•   Detailed functionality
•   Troubleshooting options
•   Technical Parameters

Remote Control

Reciever

Summary of Contents for 8-Zone RGB Remote Control










Reviews: