Smeg PGF95K-3 Instruction Manual Download

Page: 1 / 16

Summary

INSTRUCTIONS FOR SAFE AND PROPER USE_______________ 20

POSITIONING OF THE HOB _______________________________ 22

ADJUSTMENT TO DIFFERENT TYPES OF GAS _______________ 28

FINAL OPERATIONS_____________________________________ 30

USING THE HOB ________________________________________ 31

CLEANING AND MAINTENANCE ___________________________ 33

THESE INSTRUCTIONS ARE VALID ONLY FOR END USER COUNTRIES WHOSE
IDENTIFICATION SYMBOLS APPEAR ON THE COVER OF THIS MANUAL.

INSTRUCTIONS FOR THE INSTALLER: these are for the

qualified

technician

who must carry out a suitable check of the gas system,

install the appliance, set it functioning and carry out an inspection test.

INSTRUCTIONS FOR THE USER : these contain user advice,
description of the commands and the correct procedures for cleaning
and maintenance of the appliance.

Summary of Contents for PGF95K-3

















Search results

Summary of Contents for PGF95K-3

Reviews:

Related manuals for PGF95K-3

Brands by name

Popular brands

Smeg PGF95K-3, Instruction Manual

Search results

Summary of Contents for PGF95K-3

Reviews:

Related manuals for PGF95K-3

Brands by name

Popular brands