background image

Page No 1

Safety rules when using 5350A/
5350AP Impact Wrenches

– Use only impact sockets and extensions, universal

joints, etc. rated as being suitable for use with impact
wrenches.

– Prolonged exposure to vibration may cause injury.
– Read all instr uctions before using this tool. All

operators must be fully trained in its use and aware of
these safety rules.

– Do not exceed the maximum working air pressure.
– Use personal protection equipment as recommended.
– Some dust created by power sanding, sawing, grinding,

drilling, and other construction activities contains
chemicals known to cause cancer, birth defects and other
reproductive harm.

– Use only compressed air at the

recommended conditions.

– If the tool appears to malfunction,

remove from use immediately and
arrange for service and repair. If it is
not practical to remove tool from
service, then shut off the air supply
to the tool and write or have written a
warning note and attach it to the tool.

– If tool is to be used with a balancer or

other suspension device, ensure that
the tool is fir mly attached to the
suspension/support device.

– When operating the tool, always keep

the body and particularly the hands away from the work-
ing attachment fixed to the tool.

– The tool is not electrically insulated. Never use the tool

if there is any chance of coming into contact with live
electricity.

– Always when using the tool, adopt a firm footing and/or

position and grip the tool sufficiently only to overcome
any reaction forces that may result from the tool doing
work. Do not overgrip.

– Use only correct spare parts for maintenance and

repair. Do not improvise or make temporary repairs.
Major servicing and repairs should only be carried out
by persons trained to do so.

– Do not lock, tape, wire, etc. the ‘On/Off’ valve in ‘On’

position. The trigger/lever, etc. must always be free to

Vibration Level

     Less Than 6.75 Meters / Sec

2

Test Method: Tested in accordance with ISO

standards 8662 Parts 1 & 7

Noise Level: Sound Pressure Level  81.87 dB(A)

       Sound Power Level       92.87 dB(A)

Test Method: Tested in accordance with Pneurop

test code PN8NTC1 and ISO Standard 3744

Air Pressure

Recommended Working

6.2

bar

90

PSI

Maximum

6.2

bar

90

PSI

Recommended Use Of

Balancer Or Support

N0

Product Net Weight

4.60 lbs

2.07 Kg

Recommended Max.

Hose Length

30 Ft

10 M

Recommended Hose Bore

Size – Minimum

3/8 ins

10 mm

Serial No.

Model No/Nos

5350A 

Friction Ring Anvil

5350AP 

Pin Anvil

Max. RPM

8,000

Cycles Per Min.

Product Type

1/2" Air Impact Wrenches

Important

Read these instructions carefully before installing, operating,
servicing or repairing this tool. Keep these instructions in a safe
accessible place.

Operator Instructions

Includes – Foreseen Use, Work Stations, Putting Into Service,
Operating, Dismantling, Assembly and Safety Rules.

Manufacturer/Supplier

Sioux Tools,  Inc.

250 Snap-on Drive

P.O. Box 1596

Murphy, NC 28906

U.S.A.

Tel No. 828-835-9765

Fax No. 828-835-9685

CE

SAFETY MESSAGES

Personal Safety Equipment

Use – Safety Glasses

YES

Use – Safety Gloves

Use – Safety Boots

Use – Breathing Masks

Use – Ear Protectors

      YES

WARNING

Always Read Instructions
Before Using Power Tools

Always Wear Safety
Goggles

Wear Hearing Protection

Avoid Prolonged Exposure
To Vibration

Figure 1

Recommended Air Supply System

Model 5350A/5350AP

1/2" Air Impact Wrenches

Form # ZCE794

Date 2008 Dec 20/A

Summary of Contents for 5350A





















Reviews: