Form ZCE491
1
Date
2006June23/D
Form ZCE491
Date 2006June23/D
Page 1 of 8
AIR SUPPLY
The efficiency of the tool is dependent on the proper supply of clean dry air at 90 psig (6.2 bar). The use of a line filter, pressure regulator, and lubricator will
insure maximum output and service life of tools.
HOSE AND HOSE CONNECTIONS
Supply hose should be not less than 1/4" (6.35 mm) I.D. Extension hoses should be at least 3/8" (10 mm) I.D. Use couplings and fittings with at least 1/4" (6.35
mm) I.D.
LUBRICATION
An airline lubricator, set to deliver one drop per minute, is recommended. If a lubricator is not used, add .04oz. (1.2 cc, 12 to 15 drops) of SIOUX No. 288 air
motor oil into the air inlet daily.
Lubricate the gearing with SIOUX No. 1232A. The planetary gearing should be greased every 150 hours. The angle bevel gears should be greased every 8
hours.
Lubricate the angle head every 6-8 working hours with Sioux 1232A grease. The grease fitting is located on the side of the angle head.
GENERAL OPERATION
•
Start the tool by depressing the lever.
•
When changing drill bits, make sure the drill is motionless, then press and hold the locking mechanism button located on the upper housing portion of the
angle head.
SOUND AND VIBRATION READINGS
Catalog No.
Sound Pressure dBA
Sound Power dBA
Vibration m/s
2
1AM1440
71.3
82.7
Less than 2.5
1AM1441
71.3
82.7
Less than 2.5
1AM1442
71.3
82.7
Less than 2.5
1AM1451
71.3
82.7
Less than 2.5
1AM1452
71.3
82.7
Less than 2.5
1AM1540
71.3
82.7
Less than 2.5
1AM1541
71.3
82.7
Less than 2.5
1AM1542
71.3
82.7
Less than 2.5
1AM1551
71.3
82.7
Less than 2.5
1AM1552
71.3
82.7
Less than 2.5
1AM1551E
71.3
82.7
Less than 2.5
*prt PN8NTC1
*prt PN8NTC1
*per ISO8662
DECLARATION OF CONFORMITY
We, Sioux Tools Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, declare under our sole responsibility that the products
1AM1440, 1AM1441, 1AM1442, 1AM1451, 1AM1452, 1AM1540, 1AM1541, 1AM1542, 1AM1551, 1AM1552, & 1AM1551E
to which this declaration relates are in conformity with the following standard or standards or other normative document or documents:
EN 792, EN 292 Parts 1&2, ISO 8662, Pneurop PN8NTC1
following the provisions of
89/392/EEC as amended by 91/368/EEC & 93/44/EC Directives.
June 1, 2006
Murphy, North Carolina, USA
Date and place of issues
Mark S. Pezzoni
President
Power and Specialty Tools
Name and position of issuer
Signature of issuer
Original
Instructions
250 Snap-on Drive • PO Box 1596 • Murphy, NC 28906 • USA • Phone: 828-835-9765 •www.siouxtools.com
WARNING
When used improperly power tools can create hazardous situations.
Everyone using, maintaining, changing accessories or working near this tool must read, understand and follow these Safety Instructions!
Improperly used power tools can cause injury or death.
WARNING
Tools left connected to the air supply while making adjustments, changing accessories, or doing any maintenance or service on tool
can start unexpectedly.
Always remove tool from air supply and activate trigger to bleed air line before making any adjustments, changing accessories, or
doing any maintenance or service on tool.
Tools starting unexpectedly can cause injury.
SAVE THESE INSTRUCTIONS!
Read and understand these instructions before operating this tool.
INSTRUCTIONS FOR NO. 1 SERIES “1AM” AIRCRAFT ANGLE DRILLS
(SERIAL “B”)
