background image

 

RUGGEDCOM 

Operating Instructions 

Release 01/2015 

English 

 

ANT1390-4ML 

Antenna for global navigation satellite systems

 

 
RUGGEDCOM antenna for use in GPS, GLONASS and Galileo sys-
tems 

Copyright © Siemens Canada Limited 2015 

 

All rights reserved 

The reproduction, transmission or use of this document or its con-
tents is not permitted without express written authority. Offenders 
will be liable for damages. All rights, including rights created by 
patent grant or registration of a utility model or design, are re-
served. 

Disclaimer of Liability 

We have checked the contents of this manual for agreement with 
the hardware and software described. Since deviations cannot be 
precluded entirely, we cannot guarantee full agreement. However, 
the data in this manual are reviewed regularly and any necessary 
corrections included in subsequent editions. Suggestions for im-
provement are welcome. 

Technical data subject to change without prior notice. 

Siemens Canada Limited 
Industry Sector 
300 Applewood Crescent 
Concord, Ontario  
Canada, L4K 5C7 
 

Classification of safety-related notices 

This manual contains notices which you should observe to ensure 
your own personal safety, as well as to protect the product and 
connected equipment. Notices relating to your personal safety are 
highlighted by a warning triangle; notices relating to property dam-
age only do not have a warning triangle. Warnings in descending 
order according to the degree of danger are shown as follows. 

 

Danger 

indicates that death or severe personal injury 

will

 result if 

proper precautions are not taken. 

 

Warning 

indicates that death or severe personal injury 

can

 result if 

proper precautions are not taken. 

 

Caution 

with a warning triangle indicates that minor personal injury 
can result if proper precautions are not taken. 

 

Caution 

without a warning triangle indicates that damage to prop-
erty can result if proper precautions are not taken. 

 

Notice 

indicates that an undesirable result or status can occur if 
the relevant notice is ignored. 

General safety notices 

 

Warning 

Devices installed outdoors must be within the area cov-
ered by a lightning protection system. Make sure that all 
conducting systems entering from outdoors can be pro-
tected by a lightning protection potential equalization 
system. 

When implementing your lightning protection concept, 
make sure you adhere to the VDE 0182 or IEC 62305 
standard. 

 

Warning 

The device (and its components) may only be used for the 
application described in the catalog or the operating in-
structions. It may only be combined with devices or com-
ponents of other manufacturers that have been approved 
and released by Siemens. 

Correct and safe operation of the device is guaranteed 
only when it is transported, stored, set up, installed, used 
and maintained according to the recommendations. 

Qualified personnel 

Only 

qualified personnel

 should be allowed to install and 

work on this equipment. Qualified persons in the sense of the 
safety-related notices in this manual are defined as persons 
who are authorized to commission, to ground, and to tag cir-
cuits, equipment, and systems in accordance with estab-
lished safety practices and standards. 

Components of the product 

The following components are supplied with the 
ANT1390-4ML: 

 

1 ANT1390-4ML Antenna 

 

Operating Instructions 

Please check that the consignment you have received is 
complete. If it is not complete or there are signs of external 
damage, please contact your supplier or your local Siemens 
office. 

Installation 

Select a mounting location at which the reception of the  
antenna in the direction of the sky is not hindered. 

Make sure that there are no metallic surfaces above the  
antenna. 

Magnetic 

1.  Take the antenna out of the protective sleeve. 

2.  Do not remove the protective foil to avoid damaging the 

mounting surface. 

3.  Select a level, ferrous surface with a diameter of at least 

11 cm. 

4.  Secure the antenna horizontally on the mounting sur-

face using the magnets, see dimension drawing 

With screws 

1.  Take the antenna out of the protective sleeve. 

2.  Remove the protective foil. 

3.  Screw the antenna horizontally at the specified points 

with M2.5 screws, see dimension drawing

 

A5E35553757A-AA 

Reviews: