![background image](http://html.mh-extra.com/html/siemens/hub-4/hub-4_installation-instructions-manual_383747001.webp)
Siemens
Siemens
Siemens
Siemens
Siemens Industry
Industry
Industry
Industry
Industry,,,,, Inc.
Inc.
Inc.
Inc.
Inc.
Building
Building
Building
Building
Building T
TT
TTec
ec
ec
ec
echnologies Di
hnologies Di
hnologies Di
hnologies Di
hnologies Division
vision
vision
vision
vision
P/N 315-099458-9
Model HUB-4
INTRODUCTION
The Model HUB-4 Communication Card from Siemens Industry, Inc., mounts in the
CC-5 Card Cage and provides up to four independent data channels, which can be
wired as either Style 4 or Style 7 for communication to the remote XLS, MXL, XL3 or
other UL864 listed local fire alarm panel providing dry relay contacts that can be used
for event monitoring.
The HUB-4 consists of a single Main-2 board on which two COM-2 boards are
installed. In turn, up to two modem or RS-485 Interface blocks can be installed on
each COM-2 board. Each modem block installed provides a single FSK data channel.
Each RS-485 Interface block installed provides a proprietary RS-485 interface channel.
Either a RS-485 Interface or a Modem Block module can be used, dependent on
application. Table 1 describes the connections that can be made.
1
E
L
B
A
T
S
E
P
Y
T
N
O
I
T
C
E
N
N
O
C
D
N
A
S
L
E
N
A
P
E
R
I
F
D
N
A
4
-
B
U
H
L
E
N
A
P
5
8
4
-
S
R
M
E
D
O
M
B
s
s
a
l
C
)
4
e
l
y
t
S
(
A
s
s
a
l
C
)
7
e
l
y
t
S
(
B
s
s
a
l
C
)
4
e
l
y
t
S
(
A
s
s
a
l
C
)
7
e
l
y
t
S
(
3
L
X
A
/
N
A
/
N
X
M
M
X
M
M
N
A
W
C
C
N
y
l
n
o
L
X
M
A
/
N
A
/
N
0
0
3
-
I
M
C
0
0
3
-
I
M
C
L
X
M
-
I
S
F
W
1
-
M
I
N
A
/
N
d
n
a
M
1
/
W
1
-
M
I
N
k
c
o
l
B
m
e
d
o
M
A
/
N
r
o
N
A
W
C
C
N
2
-
I
M
P
r
o
t
a
r
t
n
e
c
n
o
C
S
L
X
-
I
S
F
M
P
R
/
B
U
H
B
U
H
B
U
H
A
/
N
r
e
h
t
O
s
O
I
A
W
)
6
1
-
1
(
s
O
I
A
W
)
6
1
-
1
(
A
/
N
A
/
N
N
A
W
C
C
N
y
l
n
o
Each of the four data channels is controlled by a separate micro-controller which
provides all background supervision of the data lines (to the remote panel) as well as
sending and receiving Fire Panel information to the primary micro-controller. The
information from these four channels is concentrated into a single data stream and
sent to the NCC WAN via the NIC-C or the PMI-2 Concentrator via HNET. On NCC
WAN, the HUB-4 communicates on each of four ports with either the MMX (XL3
Modem), the CMI-300 (MXL modem), NIM-1 FSI (MXL FSI modem), NIM-1W (MXL
RS-485), RPM (XLS RS-485), HUB-4 (XLS RS-485), HUB-4 (XLS modem) or up to 16
WAIO (Wide Area Input Output) boards. On the PMI-2 Concentrator, the HUB-4
communicates on each of the four ports with either the NIM-1W/NIM-1M (MXL
Modem), NIM-1W (MXL RS-485), RPM (XLS RS-485), HUB-4 (XLS RS-485), or HUB-4
(XLS modem).
Using the Modem Block module, communication distance is 8 miles (CMI-300/MMX-1)
or 10 miles (HUB-4 to HUB-4) over 18 gauge twisted pair lines depending on the quality
of the communication wires (attenuation cannot exceed -23 dBm [CMI-300/MMX-1] or
Communication Card for NCC WAN/PMI-2 Concentrator
Installation Instructions
Figure 1
HUB-4 Communication
Card