Garden Store 4 x 2 Instructions
Thank you and congratulations on the purchase of your Shire Garden Building. We
believe that this product will give you many years of excellent service. This is a natural
product manufactured to a high standard therefore if you have any queries or experience
any difficulties then please contact our customer service hotline
01945 46 89 10
or
01945 46 89 11
or
01945 46 89 12
.
Preparation of Base
We recommend that the base onto which your building will stand should be at least 75mm
larger in each direction than the total floor size of the building.
Actual floor area of the building: 1190 x 590mm
Total height clearance: 1520mm
The chosen position in your garden for the siting of the building should be excavated to
a depth of 75mm to allow a base of sand, on to which paving slabs can be evenly laid -
THEY
MUST BE LEVEL AND FIRM.
Treatment/Care of your Garden Building
Treat with a suitable decorative wood finish immediately. We recommend that all timber
pieces be treated again prior to assembly and again within 3 months of assembly. We
further recommend that all pieces are treated again at least annually or as frequently as
the instructions on the product used recommends.
We would suggest that all wall panels be treated in an upside-down position to allow the
finish/treatment to ingress into the tongue and groove jointing.
We would also remind you that you would rarely (if ever) be able to re-treat the
underside of the floor following assembly. We strongly recommend that the underside
of the floor is treated an absolute minimum of twice (not including pre-treatment).
Completed Garden Store
Tools Required
Posidrive screwdriver (electric is best)
Drill, 6mm drill bit and 8mm drill bit
Hammer
Sandpaper (to smooth any rough edges)
Cutting knife
Tape measure
Step ladder
Ruler
Pencil
Saw
IMPORTANT!
PLEASE READ PRIOR TO ASSEMBLY OF
THE BUILDING
EVERY PRECAUTION IS TAKEN TO
ENSURE THAT YOUR BUILDING HAS NO
ELEMENT INCORRECTLY PLACED OR
POSSIBLY HAZARDOUS, HOWEVER
PRIOR TO USE PLEASE CHECK ALL
SURFACES FOR THE FOLLOWING:
1 RAISED GRAIN, SPLINTERS: sand
down timber to smooth finish
2 NAIL/SCREW/PIN HEADS PROUD: tap
home to be flush with surface of timber
3 DAMAGED SCREW HEADS
RESULTING IN SHARP SPLINTERS OF
METAL: replace
4 SHARP ENDS OF NAILS/ SCREWS/
PINS PROTRUDING THROUGH THE
PANEL: remove and reposition.
5 ENSURE ALL PARTS ARE SECURED
AGAINST REASONABLE FORCE:
remove and refit
6 ENSURE THERE ARE NO LOOSE
PARTS: remove and refit/discard
WE RECOMMEND THAT PROTECTIVE
GLOVES BE WORN THROUGHOUT
QTY DESCRIPTION
Building
1 Floor
A
2 Back Panels
B
2 Side Panels
C
2 Framework 34x34x1120mm
D
2 Doors
D1
1 Door Coverstrip 46x12
D2
1 OSB Roof (1220mm x 640mm)
E
1 Piece Felt
F
6 Roof fixing blocks
G
5 Cover strips 46x12
H
2 Door (weather) strips 28x12
I
PLEASE LAY OUT PARTS AND CHECK OFF AGAINST CHECK LIST BELOW:
Wood is a natural product and is therefore
prone to changes in appearance, including
some warping, movement and splitting,
particularly during unusual climatic conditions
(long hot or wet spells of weather). As a natural
occurrence this is not covered by a guarantee.
PLEASE NOTE
BUI T AROUND OUR REPUTATION
F
E
G
G
C
H
I
I
A
B
B
D
D2
D
D1
C
QTY DESCRIPTION
Accessories
6 Door Hinges
1 Pad-Bolt & Housing
2 Bolts
4 L-Shaped Brackets
16 60mm Screws
28 40mm Nails
70 25mm Screws
50 13mm Felt Nails
8 10mm Screws
6 40mm Screws
Parts List
01/08
