manualshive.com logo in svg
background image

This document has been published to be used for

after sales service only.

The contents are subject to change without notice.

Parts marked with “

“ are important for maintaining the safety of the set. 

Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.

SHARP CORPORATION

DIGITAL COPIER

MODEL

AR-5316

(For North America)

CODE : 00ZAR5316/A1E

AR-5316

(With optional AR-SP6 installed)

[ 1 ] GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

[ 2 ] SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1

[ 3 ] CONSUMABLE PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1

[ 4 ] EXTERNAL VIEWS AND INTERNAL STRUCTURES  . . . . . . . . . . . . . . .4-1

[ 5 ] UNPACKING AND INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1

[ 6 ] ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1

[ 7 ] SIMULATIONS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1

[ 8 ] USER PROGRAMS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1

[ 9 ] TROUBLE CODE LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-1

[10] MAINTENANCE  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-1

[11] DISASSEMBLY AND ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-1

[12] FLASH ROM VERSION UP PROCEDURE  . . . . . . . . . . . . . . . . . . . . . .12-1

[13] ELECTRICAL SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13-1

CONTENTS

[00]COVER.fm  1 ページ  2005年7月1日 金曜日 午後5時36分

Содержание IMAGER AR-5316

























































Отзывы: