![background image](http://html.mh-extra.com/html/sharp/an-sv10lp/an-sv10lp_installation-manual_371868001.webp)
Printed in China
TINS-F101WJZZ
11P06-CH-NM
INSTALLATION MANUAL
CAUTION:
• Potential hazard of glass particles if lamp ruptures. Please have a Sharp Authorized Projector Dealer or
Service Center* replace lamp if rupture occurs.
• Do not remove the lamp unit directly after operation of the projector. The lamp may be extremely hot. Wait
at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool
before removing the lamp unit.
■
It is recommended that the lamp be replaced when the remaining lamp life becomes 5% or less, or when you notice a signifi -
cant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display.
IMPORTANT NOTE TO U.S. CUSTOMERS:
The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of
this projector under warranty, including lamp replacement, must be obtained through a Sharp Authorized
Projector Dealer or Service Center*. For the name of the nearest Sharp Authorized Projector Dealer or
Service Center*, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).
Hg LAMP CONTAINS MERCURY For State Lamp Disposal Information
www.lamprecycle.org or 1-800-BE-SHARP
U.S.A. ONLY
* Confi rm the name of the Dealer or Service Center referring to your projector operation manual.
LAMP UNIT (LAMP/CAGE MODULE)
FOR PROJECTOR
MODEL
AN-SV10LP
Removing and Installing the
Lamp Unit
Warning!
Do not remove the lamp unit from the projector right
after use. The lamp and parts around the lamp will
be very hot and may cause burns or injury.
•
Info
Do not touch the glass surface of the lamp unit or
the inside of the projector.
To avoid injury to yourself and damage to the lamp,
make sure you carefully follow the steps below.
Do not loosen other screws except for the lamp unit
cover and lamp unit.
•
•
•
1
Press
STANDBY/ON
on the projector
or
STANDBY
on the remote control to
put the projector into Standby mode.
2
Disconnect the power cord.
Unplug the power cord from the AC socket.
Leave the lamp until it has fully cooled down
(about 1 hour).
3
Remove the lamp unit cover.
Loosen the user service screw (
1
) that secures the
lamp unit cover. Remove the lamp unit cover (
2
).
•
•
•
1
2
3
4
Remove the lamp unit.
Loosen the securing screws from the lamp unit.
Hold the lamp unit by the handle and pull it in the
direction of the arrow. At this time, keep the lamp
unit horizontal and do not tilt it.
5
Insert the new lamp unit.
Press the lamp unit fi rmly into the lamp unit
compartment. Fasten the securing screw.
6
Replace the lamp unit cover.
Align the tab on the lamp unit cover (
1
) and close
it (
2
). Be careful not to get the strap caught in the
cover. Then tighten the user service screw (
3
) to
secure the lamp unit cover.
Info
If the lamp unit and lamp unit cover are not
correctly installed, the power will not turn on,
even if the power cord is connected to the
projector.
•
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
Info
Make sure to reset the lamp timer only when
replacing the lamp. If you reset the lamp timer and
continue to use the same lamp, this may cause the
lamp to become damaged or explode.
•
1
Connect the power cord.
Plug the power cord into the AC socket of the
projector.
2
Reset the lamp timer.
While simultaneously holding down
MENU
,
ENTER
and
R
on the projector, press
STANDBY/ON
on
the projector and keep all four buttons pressed
down until the lamp indicator starts blinking green.
“LAMP 0000H” is displayed, indicating that the
lamp timer is reset.
•
•
•
•
•
•
4
5
6
1
2
STANDBY/ON
button
AC socket
User service screw
(for lamp unit cover)
Handle
Securing screws
AC socket
ENTER button
MENU button
R
button
STANDBY/ON button
AN-SV10LP̲OptionLamp.indd 1
AN-SV10LP̲OptionLamp.indd 1
2011/05/16 13:23:55
2011/05/16 13:23:55