background image

1

32L-S400, 36L-S400
CL32S40, CL36S40

SHARP CORPORATION

This document has been published to be used for after
sales service only.
The contents are subject to change without notice.

In the interests of user-safety (Required by safety regulations in some countries ) the set should be restored to its
original condition and only parts identical to those specified should be used.

S39E632L-S400

COLOR TELEVISION

Chassis No. SN-92

SERVICE MANUAL

Page

»

 ELECTRICAL SPECIFICATIONS ......................................................................................................... 1

»

 IMPORTANT SERVICE SAFETY PRECAUTION ................................................................................. 2

»

 LOCATION OF USER'S CONTROL ..................................................................................................... 6

»

 INSTALLATION AND SERVICE INSTRUCTIONS ................................................................................ 7

»

 CHASSIS LAYOUT ............................................................................................................................. 13

»

 BLOCK DIAGRAM ............................................................................................................................. 14

»

 SCHEMATIC DIAGRAMS ................................................................................................................... 15

»

 PRINTED WIRING BOARD ASSEMBLIES ........................................................................................ 27

»

 REPLACEMENT PARTS LIST ............................................................................................................ 31

»

 PACKING OF THE SET ...................................................................................................................... 42

CONTENTS

AUDIO POWER

OUTPUT RATING .............. 2.5W + 2.5W (at 10% distortion and

Dual CH Operate)

SPEAKER

SIZE ............................................................... 12 x 6 cm (2 pcs.)

VOICE COIL IMPEDANCE ............................... 8 ohm at 400 Hz

ANTENNA INPUT IMPEDANCE

VHF/UHF .................................................... 75 ohm Unbalanced

TUNING RANGES

VHF-Channels .............................................................. 2 thru 13

UHF-Channels ............................................................ 14 thru 69

CATV Channels ........................................................... 1 thru 125

(EIA, Channel Plan U.S.A.)

POWER INPUT ..................................................... 120V  AC 60 Hz

POWER RATING

32L-S400, CL32S40 .......................................................... 140W

36L-S400, CL36S40 .......................................................... 165W

PICTURE SIZE

32L-S400, CL32S40 ................................ 3,073cm

(476sq inch)

36L-S400, CL36S40 ................................ 3,905cm

(605sq inch)

CONVERGENCE ............................................................. Magnetic

SWEEP DEFLECTION ..................................................... Magnetic

FOCUS ................................................ Hi-Bi-Potential Electrostatic

INTERMEDIATE FREQUENCIES

Picture IF Carrier Frequency ..................................... 45.75 MHz

Sound IF Carrier Frequency ...................................... 41.25 MHz

Color Sub-Carrier Frequency ..................................... 42.17 MHz

 (Nominal)

Specifications are subject to change without
prior notice.

ELECTRICAL SPECIFICATIONS

32L-S400, 36L-S400
CL32S40, CL36S40

MODELS

Summary of Contents for 32L-S400













































Reviews: