background image

1

25N-M100/M180/S100/S180
CN25M10,CN25S18/20

SERVICE MANUAL

In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its
original condition and only parts identical to those specified should be used.

S40Y525N-M100

»

 ELECTRICAL SPECIFICATIONS ........................................................................................................ 1

»

 IMPORTANT SERVICE SAFETY PRECAUTION ................................................................................ 2

»

 LOCATION OF USER'S CONTROL .................................................................................................... 6

»

 INSTALLATION AND SERVICE INSTRUCTIONS ............................................................................... 9

»

 CHASSIS LAYOUT ............................................................................................................................ 15

»

 BLOCK DIAGRAM ............................................................................................................................. 17

»

 SCHEMATIC DIAGRAMS .................................................................................................................. 21

»

 PRINTED WIRING BOARD ASSEMBLIES ....................................................................................... 45

»

 REPLACEMENT PARTS LIST ........................................................................................................... 49

»

 PACKING OF THE SET ..................................................................................................................... 59

Page

25N-M100/180
CN25M10

SHARP CORPORATION

This document has been published to be used for after
sales service only.
The contents are subject to change without notice.

CONTENTS

MODELS

ELECTRICAL SPECIFICATIONS

POWER INPUT ..................................................... 120 V AC 60 Hz
POWER RATING

25N-M100/180, CN25M10 ............................................... 105 W
25N-S100/180, CN25S18/20 ............................................ 110 W

PICTURE SIZE ........................................... 2,032cm

2

 (315sq inch)

CONVERGENCE ............................................................. Magnetic
SWEEP DEFLECTION .................................................... Magnetic
FOCUS ............................................... Hi-Bi-Potential Electrostatic
INTERMEDIATE FREQUENCIES

Picture IF Carrier Frequency ..................................... 45.75 MHz
Sound IF Carrier Frequency ...................................... 41.25 MHz
Color Sub-Carrier Frequency .................................... 42.17 MHz

 (Nominal)

AUDIO POWER

25N-M100/180, CN25M10 ............. 1.3W (at 10% distortion and

Dual CH Operate)

25N-S100/180, CN25S18/20 .. 1.3W+1.3W (at 10% distortion and

Dual CH Operate)

SPEAKER

SIZE ...................................................................... 8 cm (Round)
VOICE COIL IMPEDANCE ............................ 32 ohm at 400 Hz

ANTENNA INPUT IMPEDANCE

VHF/UHF ..................................................... 75 ohm Unbalanced

TUNING RANGES

VHF-Channels ............................................................... 2 thru 13
UHF-Channels ............................................................ 14 thru 69
CATV Channels ........................................................... 1 thru 125

(EIA, Channel Plan U.S.A.)

Specifications are subject to change without
prior notice.

25N-M100/180, 25N-S100/180
CN25M10, CN25S18, CN25S20

25N-S100/180
CN25S18/20

COLOR TELEVISION

Chassis No. SN-91

Summary of Contents for 25N-M100



















































Reviews: