![background image](http://html.mh-extra.com/html/sealife/sea-dragon-mini-1000f/sea-dragon-mini-1000f_instructions_1227785001.webp)
Sea Dragon Mini 1000F UW Photo-Video-Dive Light w/ Power Kit (
SLKITO7
)
Instructions
Sheet
Overview:
A bright 1000 lumen, wide-beam light ideal for close-up photos/videos, auto focus assist (Focusing light) and as
a powerful dive light. Includes YS adapter for mounting to Flex-Connect or YS system of trays, grips and arms (Flex-
Connect accessories sold seperately). Includes adapters for mounting to AquaPod and GoPro camera.
What’s in the
SLKITO7 Box:
Light w/ YS adapter
18650 Li-ion & charger w/ USB cable
Adapters for
Spare O-rings (2), O-ring lube
(Attached lanyard not shown)
(Note: Battery is pre-installed in the light)
AquaPod & GoPro
& O-ring removal
tool
Step 1:
Unscrew light head from grip and install one 18650-type rechargeable Li-ion battery or two single-use CR123
batteries. Batteries sold seperately. Recommend XTAR brand 18650 battery 2600 or 3500mAh for best performance.
Step 2:
Two O-rings maintain the waterproof seal.
1)
O-rings and sealing surfaces must be perfectly clean.
2)
Inspect O-rings for cuts, tears or other damage and replace
if damaged or at least once a year (item SL98103).
3)
Lube O-rings lightly before each use.
Step 3:
Push the power button down for 1 sec. to
power light on and 2 sec. to power light off.
Note:
Quick press power button to change light
modes: 100% power → 50% power →25% power →
Blinking → SOS → [repeat cycle].
Mounting options:
Use YS adapter to mount light
to any Flex-Connect or YS system of arms, grips
and trays (sold separately). Included are YS
mounts for SeaLife AquaPod and GoPro camera.
AquaPod
GoPro
Flex-Connect
Flex-Connect
Cold Shoe mount Grip/Tray mount
Important:
1)
After each dive, soak the sealed light in fresh water for about 20
minutes to remove any residual salt, sand and dirt. Dry light with
clean towel before opening battery compartment or storage.
2)
A battery indicator light is located around power button. Green =
full power, yellow = half power and red = low power
(Replace/recharge battery).
3)
The light is designed for underwater use. Water displaces heat and
prevents the light from overheating. Avoid using the light on land
for prolonged periods of time or it will become hot and may cause
burning if touched. A thermal sensor will dim the light if internal
temperature exceeds 150°F (65°C).
Guarantee:
SeaLife warrants the original purchaser of this product, for a
period of one (1) year from the date of purchase, that the product is free from
defects in workmanship and materials. In the event the original purchaser
believes there is a defect in a product, it is recommended that the purchaser
first visit sealife-cameras.com for product updates and repair service
information. Please contact your local SeaLife dealer or the importer in the
country where the product was purchased for return information.
SeaLife (Div. of Pioneer Research), 97 Foster Road, Moorestown, NJ 08057 USA
September 2019
Battery warning:
Only use 18650 battery with button-top (not flat-top), integrated protected circuit, minimum 2600
mAh, minimum 3.5A discharge current and cell made by Panasonic/Sanyo Japan or Samsung Korea. Two single-use CR123
batteries may also be used. Never use rechargeable CR123 batteries. Using a non-conforming battery is a potential safety
hazard and may damage the light. Recommend using Xtar brand 18650 Li-ion button-top battery with 2600Ah or higher.
Remove battery before storage. Do not use any battery that has been exposed to water or is damaged in any way. Do not
power on the light if water has entered the light. Remove the battery and contact your local authorized SeaLife dealer for
service. Dispose batteries in accordance with your local regulations.