background image

INSTRUCTIONS FOR:

DEHUMIDIFIERS

MODEL NOS:

XRC25, 40, 55 & 90

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions 

and properly maintained, give you years of trouble free performance.

XRC25,40,55,90 - 1 - 060503

IMPORTANT:

PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.

USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE

DAMAGE OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

1.1.

ELECTRICAL SAFETY

p  

WARNING!

It is the responsibility of the owner and the operator to read, understand and comply with the following:

You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other

connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices.

A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend that a Residual Current

Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into a supply which is not protected

by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer. 

You must

also read and understand the following instructions concerning electrical safety.

1.1.1. The 

Electricity at Work Act 1989 

requires that all portable electrical appliances, if used on business premises, are tested by a qualified

electrician, using a Portable Appliance Tester (PAT), at least once a year.

1.1.2. The 

Health & Safety at Work Act 1974 

makes owners of electrical appliances responsible for the safe condition of those appliances

and the safety of the appliance operators. 

If in any doubt about electrical safety, contact a qualified electrician.

1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1. and 1.1.2.

and use a Portable Appliance Tester.

1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check all

connections to ensure that none is loose.

1.1.6.

Important:

Ensure that the voltage marked on the appliance matches the power supply 

to be used and that the plug is fitted with the correct fuse - see fuse rating at right.

1.1.7.

DO NOT

pull or carry the appliance by the power cable.

1.1.8.

DO NOT 

pull the plug from the socket by the cable.

1.1.9.

DO NOT

use worn or damaged cables, plugs or connectors. Immediately have any faulty

item repaired or replaced by a qualified electrician. When a BS 1363/A UK 3 pin plug is 

damaged, cut the cable just above the plug and 

dispose of the plug safely. 

Fit a new plug according to the following instructions (UK only).

a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.

b) Connect the BROWN live wire to the live terminal ‘L’.

c) Connect the BLUE neutral wire to the neutral terminal ‘N’.

d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer insulation

extends beyond the cable restraint and that the restraint is tight.

Double insulated products, which are always marked with this symbol      , are fitted with live (brown) and neutral (blue) wires only.

To rewire, connect the wires as indicated above - 

DO NOT

connect either wire to the earth terminal.

1.1.10. Products which require more than 13 amps are supplied without a plug. In 

this case you must contact a qualified electrician to ensure that a suitably 

rated supply is available. We recommend that you discuss the installation of an 

industrial round pin plug and socket with your electrician.

1.1.11. If an extension reel is used it should be fully unwound before 

connection. A reel with an RCD fitted is preferred since any appliance

plugged into it will be protected. The cable core section is important and 

should be at least 1.5mm

2

, but to be absolutely sure that the capacity of 

the reel is suitable for this product and for others which may be used in the

other output sockets, we recommend the use of 2.5mm

2

section cable.

1. SAFETY INSTRUCTIONS

FUSE RATING 13 AMP

Blue

Neutral 

Wire

Yellow & Green 

Earth Wire 

Cable 

Restraint

Brown

Live 

Wire

1.2

GENERAL SAFETY

p

WARNING!

Disconnect the dehumidifier from the mains power before 

servicing or performing any maintenance.

3

Maintain the dehumidifier in good condition (use an authorised service agent).

3

Replace or repair damaged parts. 

Use genuine parts only. Non-authorised 

parts may be dangerous and will invalidate the warranty.

3

Use dehumidifier only on level and solid floors.

7

DO NOT

use the dehumidifier for any purpose other than that for which it 

is designed.

7

DO NOT

operate the dehumidifier if any parts are damaged or missing as 

this may cause failure and/or personal injury.

7

DO NOT

allow untrained persons to operate the dehumidifier.

7

DO NOT

use the dehumidifier where there are flammable liquids, solids or 

gases such as paint solvents, etc.

7

DO NOT

pull the cord from the power supply.

3

When not in use switch off the dehumidifier, remove plug from the power supply.

Reviews: