background image

Axle StAndS (pAir) 
2tonne cApAcity per StAnd

model no: 

VS2002HV, VS2002Bl, VS2002or

thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these 

instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT:

 PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE 

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR 
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1.  SAfety

 

‰

 

WArninG! do not oVerloAd Axle StAndS Beyond rAted cApAcity. oVerloAdinG cAn cAUSe dAMAGe to, or 

fAilUre of, tHe Axle StAndS. poSition loAd on centre of crUtcH/SAddle only. AlWAyS USe StAndS in pAirS 

on HArd leVel SUrfAce cApABle of SUStAininG tHe loAd. USe of StAndS on otHer tHAn HArd leVel SUrfAceS 

cAn reSUlt in loAd inStABility And poSSiBle loSS of loAd. do not USe on tArMAcAdAM.  fAilUre to folloW 

tHeSe inStrUctionS MAy reSUlt in dAMAGe to Axle StAndS, loSS of loAd reSUltinG in property dAMAGe, 

SerioUS perSonAl inJUry or loSS of life.

 

dAnGer! GreAt cAre MUSt Be tAKen to enSUre yoU loWer tHe VeHicle (or otHer loAd) 

SloWly And cArefUlly onto tHe centreS of tHe crUtcH/SAddle of tHe Axle StAndS.

 

9

Use only as specified by the manufacturer.

 

9

ensure the load does not exceed the maximum capacity as marked on the axle stand, per pair.

 

9

Use no more than a single pair of stands either on the front, rear or one side of the vehicle. Use in pairs.

 

9

no alterations or modifications shall be made to this product.

 

9

Use on a hard, level surface, e.g. concrete. 

do not

 use on uneven ground or tarmacadam.

 

9

Securely chock wheels in contact with the ground. Before jacking and placing the stands, apply vehicle handbrake 

(put automatics in ‘Park’).

 

9

make sure that each stand is securely located under a strong point on the vehicle; consult the vehicle manufacturer’s 

handbook for guidance. ensure that height adjust locking mechanism is fully located before applying any load to 

the axle stand.

 

9

ensure that the load is located centrally on the saddle, and that the weight is directed through the vertical axis of 

the stand.

 

9

exercise extra care when using with a three wheeled vehicle or a trailer. Refer to vehicle manufacturer’s 

instructions.

 

9

once vehicle is supported, ensure that the vehicle and stands are stable before starting work. ensure that it is not possible for the 

vehicle to move before commencing any work.

 

9

Inspect stands before each use. 

do not

 use if they show signs of damage. 

do not 

use if it is suspected that they have been 

overloaded.

 

9

Before commencing any work or going beneath the vehicle, undertake a risk assessment. ensure that a responsible person is aware of 

the work about to be undertaken.

 

9

Replace any labels on the axle stand should they become unreadable. This applies in particular to any warning or operation instruction 

labels. If replacement labels are required, contact your Sealey stockist.

 

8

do not 

use axle stands on the highway, or anywhere else if it is deemed to be unsafe.

 

8

do not

 push or twist the vehicle/load whilst it is supported on stands.

 

8

do not

 mix components between stands. Use only as supplied.

 

8

do not

 allow children or animals in the vicinity of a vehicle supported on axle stands.

 

8

do not

 leave a vehicle on axle stands in an area that could be considered a hazard to others or property. 

 

9

folloW StepS 1, 2, And 3 to correctly plAce VeHicle / loAd onto Axle StAndS.

VS2002HV, Bl,oR Issue 1 31/05/18

Original Language Version

© Jack Sealey limited

Refer to 

instructions

Reviews: