![background image](http://html.mh-extra.com/html/sealey/vma913/vma913_instructions_1227429001.webp)
INSTRUCTIONS FOR:
Auto VAlet MAchine
MODEL No:
VMA913
1. SAFetY inStRuctionS
IMPORTANT:
PleASe ReAD theSe inStRuctionS cAReFullY. note the SAFe oPeRAtionAl ReQuiReMentS, WARninGS & cAutionS.
uSe the PRoDuct coRRectlY AnD With cARe FoR the PuRPoSe FoR Which it iS intenDeD. FAiluRe to Do So MAY cAuSe
DAMAGe AnD/oR PeRSonAl inJuRY AnD Will inVAliDAte the WARRAntY. PleASe KeeP inStRuctionS SAFe FoR FutuRe uSe.
1.2
GeneRAl SAFetY
Disconnect the machine from mains power supply before servicing, changing accessories, or performing any maintenance.
Use genuine accessories and parts only
(unauthorised accessories and parts may be dangerous, and will invalidate your warranty).
Maintain the Valet machine in good condition. Use authorised agent for servicing. Keep machine clean, but
DO NOT use solvents.
Ensure the correct filter is firmly in place before operating the Auto Valet.
Wrong filters will invalidate your warranty.
Wear protective clothing and gloves.
DO NOT allow children or untrained persons to operate the unit.
DO NOT place attachments close to your face (especially eyes, ears, etc). Do not point the hose end at other persons or animals.
WARninG!
DO NOT get detergent on flesh. If contact is made wash immediately. NEVER allow detergent near eyes, or mouth. If contact
is made, thoroughly rinse and seek medical advice. If swallowed, seek immediate medical advice. Follow instructions on the detergent container
DANGER!
DO NOT vacuum hot, or glowing ash, cigarette ends,
inflammable, explosive, corrosive or dangerous liquids, solids or dusts.
DO NOT operate the unit without the correct filter for the type of job. Make sure
the filter is firmly in place.
DO NOT operate the pump switch when there is no liquid in the detergent tank. The vacuum motor runs independently of the pump.
DO NOT leave machine running unattended. Turn power supply OFF, and DO NOT leave the vicinity until motor has come to a complete stop.
DO NOT operate the Auto Valet while under the influence of drugs, alcohol or impairing medication, or if you are fatigued.
DO NOT force the Auto Valet to achieve a task it is not designed to perform.
DO NOT clean the filters with solvents. When not in use store the valet machine in a safe, dry, childproof location.
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance
1.1.
electRicAl SAFetY
WARninG!
It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other
connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices. A
Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend that a Residual Current
Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into a supply which is not protected
by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer.
You must
also read and understand the following instructions concerning electrical safety.
1.1.1. The
electricity at Work Act 1989
requires that all portable electrical appliances, if used on business premises, are tested by a
qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The
health & Safety at Work Act 1974
makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators.
if in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1. and 1.1.2.
and use a Portable Appliance Tester.
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check all
connections to ensure that none is loose.
1.1.6.
important:
Ensure that the voltage marked on the appliance matches the power supply
to be used and that the plug is fitted with the correct fuse - see fuse rating at right.
1.1.7.
Do not
pull or carry the appliance by the power cable.
1.1.8.
Do not
pull the plug from the socket by the cable.
1.1.9.
Do not
use worn or damaged cables, plugs or connectors. Immediately have any faulty
item repaired or replaced by a qualified electrician. When a BS 1363/A UK 3 pin plug is
damaged, cut the cable just above the plug and
dispose of the plug safely.
Fit a new plug according to the following instructions (UK only).
a) connect the GReen/YelloW earth wire to the earth terminal ‘e’.
b) connect the BRoWn live wire to the live terminal ‘l’.
c) connect the Blue neutral wire to the neutral terminal ‘n’.
d) After wiring, check that there are no bare wires, that all wires have been correctly
connected, that the cable outer insulation extends beyond the cable restraint and
that the restraint is tight.
Double insulated products, which are always marked with this symbol , are fitted with live (brown) and neutral (blue) wires only.
To rewire, connect the wires as indicated above -
Do not
connect either wire to the earth terminal.
1.1.10. If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any appliance
plugged into it will be protected. The cable core section is important and should be at least 1.5mm², but to be absolutely sure that the
capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use
of 2.5mm² section cable.
FuSe RAtinG
13 AMP
Blue
Neutral
Wire
Yellow & Green
Earth Wire
Cable
Restraint
Brown
Live
Wire
Original Language Version
VMA913 Issue: 2 - 18/01/10