2TONNE AIR JACKING BEAM WITH 1.6M
EXTENDING ARMS & FLAT ROLLER
SUPPORTS
MODEL NO:
SJBEX200A
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
I
MP
PO
R
RTA
TANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
TH
HE
P
PR
O
ODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PE
ER
S
SON
NAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
Familiarise yourself with the applications, limitations and hazards of the jacking beam.
Maintain the jacking beam in good condition (use an authorised service agent).
Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the
warranty.
Inspect the jacking beam before each use.
DO NOT
use the jacking beam if it is damaged, altered, modi
fi
ed, in poor condition, leaking hydraulic
fl
uid, or unstable due to
missing
components.
DO NOT
alter or modify the jacking beam in any way.
DO NOT
load the jacking beam beyond it’s rated capacity.
DO NOT
allow untrained persons to operate the jacking beam.
DO NOT
use the jacking beam for purposes other than that for which it is intended.
DO NOT
use the centre saddle if the work to be performed can cause the load to move.
DO NOT
operate the jacking beam when you are tired or under the in
fl
uence of alcohol, drugs or intoxicating medication.
Remove
ill
fi
tting clothing. Remove ties, watches, rings, other loose jewellery and contain long hair.
Maintain correct balance and footing. Ensure the
fl
oor is not slippery and wear non-slip shoes.
Consult the vehicle manufacturer for the correct lifting locations.
Ensure the vehicle is in PARK (automatics) and the handbrake is on before attempting to raise the vehicle.
Only use the saddles provided with the jacking beam.
Ensure the set-up is stable and secure before lifting. Be aware of pinch points.
This is a lifting device only.
Ensure the load is central on saddles before lifting.
The jacking beam can only be used to lift one end of the vehicle.
Ensure that there are no persons or obstructions beneath the vehicle before lowering.
Always lower the load slowly and carefully.
WARNING!
Ensure correct air pressure is maintained and not exceeded. Recommended pressure 90-145psi.
DO NOT
pull the hose from the air supply.
DO NOT
direct air from the air hose at yourself or others.
Disconnect the jacking beam from the air supply prior to removing jacking beam from the ramp or pit and store in a safe, dry
childproof
location.
WARNING!
Place the vehicle on axle stands prior to commencing any operations.
WARNING! The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible
conditions and situations that may occur. It must be understood that common sense and caution are factors
which cannot be built into this product, but must be applied by the operator.
2. INTRODUCTION
Jacking beam lifts load with compressed air. Fully certi
fi
ed and approved to comply with MOT requirements. Features 2-stage mechanical
safety lock and telescopic
fi
nger guards to prevent accidental injury. Supplied with two pairs of aluminium support blocks. Beam has
spring loaded
fl
at arms with roller bearings - when unloaded, these support the weight of the beam, allowing the entire unit to run smoothly
along the pit or ramp, but when loaded, they
fi
rmly stabilise the unit. Optional hook arms supplied. Wide lift con
fi
guration meets MOT
recommendation for lifting on jacking point.
3. SPECIFICATION
Model No: ...........................................................SJBEX200A
Air pressure: .......................................................... 90-145psi
Beam lift: ............................................................... 95-300mm
Capacity: ..................................................................... 2tonne
Load arm reach: ................................................ 850-1600mm
Support arm reach: ........................................... 780-1075mm
SJBEX200A Issue 1 05/10/21
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Wear eye
protection
Wear protective
gloves
Wear safety
footwear
Wear protective
clothing
