1.1. ELECTRICAL SAFETY
WARNING!
It is the responsibility of the owner and the operator to
read, understand and comply with the following: You must check all
electrical products, before use, to ensure that they are safe. You must
inspect power cables, plugs, sockets and any other connectors for wear
or damage. You must ensure that the risk of electric shock is minimised
by the installation of appropriate safety devices. A Residual Current
Circuit Breaker (RCCB) should be incorporated in the main distribution
board. We also recommend that a Residual Current Device (RCD) is
used. It is particularly important to use an RCD with portable products
that are plugged into a supply which is not protected by an RCCB. If in
any doubt consult a qualified electrician. You may obtain a Residual
Current Device by contacting your Sealey dealer. You must also read and
understand the following instructions concerning electrical safety.
1.1.1. The
Electricity at Work Act 1989
requires that all portable
electrical appliances, if used on business premises, are
tested by a qualified electrician, using a Portable Appliance
Tester (PAT), at least once a year.
1.1.2. The
Health & Safety at Work Act 1974
makes owners of
electrical appliances responsible for the safe condition of
those appliances and the safety of the appliance operators.
If in any doubt about electrical safety, contact a qualified
electrician.
1.1.3. Ensure that the insulation on all cables and on the appliance is
safe before connecting it to the power supply. See 1.1.1. and
1.1.2. and use a Portable Appliance Tester.
1.1.4. Ensure that cables are always protected against short circuit
and overload.
1.1.5. Regularly inspect power supply cables and plugs for wear or
damage and check all connections to ensure that none is loose.
1.1.6.
Important:
Ensure that the voltage marked on the appliance
matches the power supply to be used and that the plug is fitted
with the correct fuse - see fuse rating below.
1.1.7.
DO NOT
pull or carry the appliance by the power cable.
1.1.8.
DO NOT
pull the plug from the socket by the cable.
1.1.9.
DO NOT
use worn or damaged cables, plugs or connectors.
Have any faulty item repaired or replaced immediately by a
qualified electrician. When a BS 1363/A UK 3 pin plug is
damaged, cut the cable just above the plug and dispose of the
plug
safely.
Fit a new plug according to the following instructions (UK only).
a) Connect the GREEN/YELLOW earth wire to the earth
terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all
wires have been connected
correctly, that the cable outer
insulation extends beyond the
cable restraint and that the
restraint is tight.
Double insulated products, which
are always marked with this
symbol , are fitted with live
(brown) and neutral (blue) wires
only. To rewire, connect the wires
as indicated in diagram.
DO NOT
connect either wire to the earth
terminal.
1.1.10.Products which require more than
13A are supplied without a plug. In
this case you must contact a
qualified electrician to ensure that
a suitably rated supply is available.
INSTRUCTIONS FOR:
COMPRESSOR 100ltr V-Twin DIRECT DRIVE 3hp
MODEL No:
SAC10030VE
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
SAC10030VE Issue No: 2(I) - 17/04/14
We recommend that you discuss the installation of an
industrial round pin plug and socket with your electrician.
IMPORTANT!
The use of extension leads to connect these
compressors to the mains is not recommended as the
resulting voltage drop reduces motor, and therefore pump
performance.
1.2. GENERAL SAFETY
3
Familiarise yourself with the application and limitations of the
compressor.
3
Ensure the compressor is in good order and condition before
use. If in any doubt do not use the unit and contact an
electrician/service agent.
WARNING!
Compressor must only be serviced by an
authorised agent. DO NOT tamper with, or attempt to
adjust, pressure switch or safety valve.
3
Before moving, or maintaining the compressor ensure it is
unplugged from the mains supply and that the air tank
pressure has been vented.
3
Maintain the compressor in good condition and replace any
damaged or worn parts. Use genuine parts only.
Unauthorised parts may be dangerous and will invalidate
your warranty.
3
Read the instructions relating to any accessory to be used
with this compressor. Ensure the safe working pressure of
any air appliance used exceeds compressors output
pressure. If using a spray a gun, check that the area selected
for spraying is provided with an air change/ventilation system.
3
Ensure the air supply valve is turned off before disconnecting
the air supply hose.
3
To move the compressor use the handle only. Maintain unit’s
centre of gravity when lifting.
DO NOT
attempt to lift or move
the compressor by any other means.
RECOMMENDED
FUSE RATING:
13A
Original Language Version
© Jack Sealey Limited
Guide to symbols
Warning:
Electricity
Warning:
Hot Surface
Warning:
Automatic
start up
Wear ear protection
Read the instruction
manual before use
DO NOT
open the air
cock before an air hose
is attached
DO NOT
operate the
compressor with
enclosure displaced
Ensure oil level is
correct before first use
