Sealey SA682.V2, Instructions

Page: 1 / 2

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE OR PERSONAL INJURY AND WILL INVALIDATE THE
WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
3 Follow all workshop safety rules, regulations, and conditions when using wrench.
p WARNING! Disconnect from air supply before changing accessories or servicing.
3 Maintain the wrench in good condition and replace any damaged or worn parts. Use genuine parts
only. Non-authorised parts may be dangerous and will invalidate the warranty.
p WARNING! Check correct air pressure is maintained and not exceeded. We recommended 90psi.
3 Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure
that all connections are secure.
3 Only use impact sockets which are specifically designed for use with an impact wrench.
3 Wear approved safety eye/face shield, ear defenders, and hand protection.
p WARNING! Due to the possible presence of asbestos dust from brake linings, when working around vehicle
brake systems we recommend you wear suitable respiratory protection
3 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3 Keep children and unauthorised persons away from the working area.
7 DO NOT use the wrench for a task it is not designed to perform.
p
p
WARNING! DO NOT use wrench if damaged or thought to be faulty. (Contact Service Agent).
7 DO NOT use wrench unless you have been instructed in its use by a qualified person.
7 DO NOT drop, throw or abuse the wrench as it is a precision tool.
7 DO NOT carry the wrench by the air hose, or yank the hose from the air supply.
7 DO NOT operate wrench if you are tired, under the influence of alcohol, drugs or intoxicating medication.
7 DO NOT carry wrench with your hand on the power trigger in order to avoid unintentional starting.
7 DO NOT direct air from the air hose at yourself or others.
SA682.V2, SA683.V2 - (2) -170203
INSTRUCTIONS FOR
AIR IMPACT WRENCH
Models:
SA682.V2, SA683.V2
2. INTRODUCTION & SPECIFICATIONS
MODEL . . . . . . . . . . . . . . . .SA682.V2
Drive size . . . . . . . . . . . . . . . . . .1”Sq
Working/Max torque . . .1400/1600ft/lb
Ultimate torque . . . . . . . . . . .1800ft/lb
Air consumption . . . . . . . . . . . . 42cfm
Operating pressure . . . . . . . . . . .90psi
Air inlet size . . . . . . . . . . . . . 1/2” BSP
Weight . . . . . . . . . . . . . . . . . . . . .22kg
MODEL . . . . . . . . . . . . . . . .SA683.V2
Drive size . . . . . . . . . . . . . . . . . . .1”Sq
Working/Max torque . . . .1100/1450ft/lb
Ultimate torque . . . . . . . . . . . .1800ft/lb
Air consumption . . . . . . . . . . . . 42cfm
Operating pressure . . . . . . . . . . .90psi
Air inlet size . . . . . . . . . . . . . 1/2” BSP
Weight . . . . . . . . . . . . . . . . . . . . .22kg
Heavy duty 1" pistol grip air wrench suitable for commercial and agricultural vehicle use. Pin clutch mechanism
gives high power:weight ratio. 4-Position torque control with reverse. Supplied with side handle and spring
balance hoop. Model SA683 is fitted with long anvil for areas with restricted access.
Issue Date: 170203
Issue No:
1
Item Part No Description
1 SA682.V2-01 MOTOR HOUSING
2 SA682.V2-02 END CAP/REAR COVER
3 SA682.V2-03 END CAP/REAR GASKET
4 SA682.V2-04 SCREW
5 SA682.V2-05 SPRING WASHER
6 SA682.V2-06 ANVIL BUSHING
7 SA682.V2-07 OIL SEAL
8 SA682.V2-08 CLUTCH HOUSING
9 SA682.V2-09 FRONT GASKET
10 SA682.V2-10 SCREW
11 SA682.V2-11 SCREW/OIL PLUG
12 SA682.V2-12 HANDLE DEAD
13 SA682.V2-13 SCREW
14 SA682.V2-14 SPRING WASHER
15 SA682.V2-15 PROTECTING RUBBER
16 SA682.V2-16 REAR PROTECTION RING
17 SA682.V2-17 MUFFLE PLATE/EXHAUST
18 SA682.V2-18 HANGER
19 SA682.V2-19 SCREW
20 SA682.V2-20 TRIGGER
21 SA682.V2-21 SPRING PIN
22 SA682.V2-22 THROTTLE BUSHING
23 SA682.V2-23 THROTTLE PIN
24 SA682.V2-24 TEFLON BALL
25 SA682.V2-25 SPRING
26 SA682.V2-26 HOSE ADAPTOR
27 SA682.V2-27 DUST COVER/BOOT
28 SA682.V2-28 SOCKET/OIL PLUG
29 SA682.V2-29 O-RING
30 SA682.V2-30 VALVE SLEEVE
31 SA682.V2-31 REVERSE VALVE
Item Part No Description
32 SA682.V2-32 PIN
33 SA682.V2-33 STEEL BALL
34 SA682.V2-34 SPRING
35 SA682.V2-35 SNAP/C-RING
36 SA682.V2-36 LEVER REVERSE
37 SA682.V2-37 SPRING PIN
38 B/6005 BEARING
39 SA682.V2-39 OIL SEAL
40 SA682.V2-40 FRONT END PLATE
41 SA682.V2-41 O-RING
42 SA682.V2-42 PIN,CYLINDER
43 SA682.V2-43 CYLINDER
44 SA682.V2-44 ROTOR
45 SA682.V2-45 ROTOR BLADE
46 SA682.V2-46 REAR END PLATE
47 B/6204Z BEARING
48 SA682.V2-48 SPRING PIN
49 SA682.V2-49 SPRING PIN
50 SA682.V2-50 HAMMER CAGE
51 SA682.V2-51 DRIVE CAM BASE
52 SA682.V2-52 STEEL BALL
53 See below DRIVE CAM
54 SA682.V2-54 HAMMER BAR
55 SA682.V2-55 SPRING
56 See below ANVIL 2”& 6”
57 SA682.V2-57 ANVIL WASHER
60 SA682.V2-60 O-RING
61 SA682.V2-61 ANVIL COLLAR
62 SA682.V2-62 SCREEN
63 SA682.V2-63 SPRING PIN
PARTS EXCLUSIVE TO SA682.V2
53 SA682.V2-53 DRIVE CAM
56 SA682.V2-56 ANVIL 2”
PARTS EXCLUSIVE TO SA683
53 SA680/55 DRIVE CAM
56 SA681/58 ANVIL 6”
BOTH MODELS SHARE COMMOM PARTS EXCEPT THOSE SHOWN BELOW
PARTS INFORMATION FOR:
AIR IMPACT WRENCH
Models: SA682.V2
& SA683.V2