![background image](http://html1.mh-extra.com/html/sealey/sa32-v2/sa32-v2_instructions_1226559001.webp)
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.
SAFETY INSTRUCTIONS
p
WARNING!
Ensure Health & Safety, local authority and general workshop practice regulations are adhered to
when using this equipment.
p
WARNING!
Disconnect from air supply before changing accessories or servicing.
3
Maintain the sander in good condition (use an authorised service agent).
3
Replace or repair damaged parts.
Use genuine parts only. Unauthorised parts may be dangerous and
will invalidate the warranty.
3
Use in suitable, clean and tidy work area, free from unrelated materials. Ensure that there is adequate lighting.
3
Before each use check abrasive for condition. If worn or damaged replace immediately.
3
Ensure the correct abrasive pad size is used.
3
Ensure there are no flammable or combustible materials near the work area.
p
WARNING!
Always wear approved eye or face and hand protection when operating the sander.
3
Use face, dust, or respiratory protection in accordance with COSHH regulations.
3
Depending on the task, sander noise level may exceed 85dB, in which case wear safety ear defenders.
3
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain and/or tie
back long hair.
3
Wear appropriate protective clothing and keep hands and body clear of working parts.
3
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3
Keep children and unauthorised persons away from the work area.
3
Check moving parts alignment on a regular basis.
3
Ensure that workpiece is secure before operating the sander. Never hold a workpiece by hand.
3
Check the workpiece to ensure that there are no protruding screws, bolts, nuts, nails, stones, etc.
3
Avoid unintentional starting.
p
WARNING!
Ensure correct air pressure is maintained and not exceeded. Recommended pressure 70-90psi.
3
Keep air hoses away from heat, oil and sharp edges. Check air hose for wear before each use and ensure
that all connections are secure.
3
Prolonged exposure to vibration from this sander poses a health risk. It is the owners responsibility to correctly
assess the potential hazard and issue guidelines for safe periods of use and offer suitable protective equipment.
7
DO NOT use the sander for a task it is not designed to perform.
7
DO NOT operate sander if any parts are damaged or missing as this may cause failure and/or personal injury.
p
WARNING!
DO NOT sand any materials containing asbestos.
7
DO NOT carry the sander by the hose, or yank the hose from the air supply.
7
DO NOT force, or apply heavy pressure to, the sander. Let the sander do the work.
7
DO NOT place attachments close to your face and do not point at other persons or animals.
7
DO NOT operate sander when you are tired or under the influence of alcohol, drugs or intoxicating medication.
7
DO NOT use sander where there are flammable liquids, solids or gases such as paint solvents and including
waste wiping or cleaning rags etc.
7
DO NOT carry the sander with your hand on the power lever.
7
DO NOT direct air from the air hose at yourself or others.
SA32.V2 - 1 - 090904
INSTRUCTIONS FOR:
TWIN PISTON IN-LINE SANDER
Model: SA32.V2
PARTS FOR:
TWIN PISTON IN-LINE SANDER
Model: SA32.V2
Item
Part No.
Description
1
SA32.V2-01
AIR INLET
2
SA32.V2-02
SCREW
3
SA32.V2-03
REAR COVER
4
SA32.V2-04
SPRING
5
SA32.V2-05
O-RING
6
SA32.V2-06
VALVE STEM
7
SA32.V2-07
VALVE PLUG
8
SA32.V2-08
VALVE COLLAR
9
SA32.V2-09
OIL COTTON
10
SA32.V2-10
OIL COTTON
11
SA32.V2-11
GASKET
12
SA32.V2-12
FLAT GEAR
13
SA32.V2-13
RIVET
14
SA32.V2-14
PISTON
15
SA32.V2-15
PISTON RING
16
SA32.V2-16
CYLINDER
17
SA32.V2-17
SCREW
18
SA32.V2-18
SPRING PIN
19
SA32.V2-19
TRIGGER
20
SA32.V2-20
HANDLE
21
SA32.V2-21
SCREW
22
SA32.V2-22
PLUG
23
SA32.V2-23
O-RING
24
SA32.V2-24
PIN
25
SA32.V2-25
SWITCH
26
SA32.V2-26
PALM HANDLE
27
SA32.V2-27
BODY
Item
Part No.
Description
28
SA32.V2-28
FRONT COVER
29
SA32.V2-29
WIRE CLIP
30
SA32.V2-30
RIVET
31
SA32.V2-31
COMPRESSION SPACER
32
SA32.V2-32
FIXED PLATE
33
SA32.V2-33
SCREW
34
SA32.V2-34
FOAM PAD
35
SA32.V2-35
PAD ASSEMBLY (PARTS 29,30,31,32,34,35)
36
SA32.V2-36
RIVET
37
SA32.V2-37
RIVET
38
SA32.V2-38
PAD PLATE
39
SA32.V2-39
LOCKING NUT
40
SA32.V2-40
SIDE GEAR
41
SA32.V2-41
BRASS PLATE
42
SA32.V2-42
SCREW
43
SA32.V2-43
TRANSMISSION GEAR
44
SA32.V2-44
GEAR SHAFT
45
SA32.V2-45
SWITCH GEAR
46
SA32.V2-46
SWITCH SLEEVE
47
SA32.V2-47
PLATE GUIDE
48
SA32.V2-48
SCREW
50
SA32.V2-50
SCREW
51
SA32.V2-51
RIVET
52
SA32.V2-52
PLUG
53
SA32.V2-53
NEEDLE BEARING
54
SA32.V2-54
FRONT GASKET
Issue No:
1
Date Issued: 090904
01284 757500
01284 703534
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
www.sealey.co.uk
Web
01284 757500
01284 703534
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
www.sealey.co.uk
Web
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT:
No liability is accepted for incorrect use of product.
WARRANTY:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION:
For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.