WARNING!
ALWAYS USE LOAD RATED STANDS TO SUPPORT LIFTED LOADS.
▲
DANGER! Use the jack for lifting and lowering only.
▲
DANGER!
DO NOT
place any part of the body beneath the lifted load unless the load is fully supported by rated stands.
▲
DANGER!
DO NOT
place any part of the body beneath the load during lifting or lowering.
DO NOT
exceed the rated capacity of the jack, load or maximum stroke.
DO NOT
adjust the overload valve, modify or use the jack for any purpose other than for which it is designed
(lifting and lowering
mechanical devices).
DO NOT
leave elevated loads unattended, unless safe from others in a garage or workshop.
DO NOT
modify the jack.
Ensure the jacking area is solid and level. Increase the jacking area with a solid flat plate (steel) if jacking on tarmacadum or grass.
Keep others away from the work area.
Ensure the jacking area is clutter free and that there is adequate lighting.
InstructIons For:
PREMIER BOTTLE JACK 3TONNE 5TONNE
8TONNE 10TONNE 12TONNE 15TONNE
modEl nos:
PBJ3:PBJ5:PBJ8:PBJ10:PBJ12:PBJ15
WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that
may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into
this product, but must be applied by the operator.
1. SAFETY
3. SPECIFICATION
4. OPERATION
2. INTRODUCTION
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
Fitted with safety overload valve and manufactured in the Eu. All steel, one-piece base, reservoir and pump cylinder design gives added
strength. Fully serviceable ram piston with extension screw. All models supplied with 90° rotating pump and telescopic pump lever. service kits
readily available.
other text:
IMPORTANT SAFETY WARNING! ALWAYS USE RATED STANDS.
Please remember a jack is a lifting and lowering device and is not designed to support a load. never get underneath a vehicle supported only
by a jack; your life is at risk. We stock a comprehensive range of axle stands, for example, please see relevant catalogue section for full details.
the jack is not limited to vehicle use only, with many applications in the engineering and construction industries.
Model
No PBJ3
PBJ5
PBJ8
PBJ10
PBJ12
PBJ15
capacity
(tonne):
3 5 8 10
12
15
minimum
Height
(mm):
[leadscew
retracted].
170 212 219 219 226 228
maximum
Height
(mm):
[leadscrew
extended].
350 437 444 444 452 452
Hydraulic
lift
(mm):
115 150 150 150 150 150
screw
Extension
(mm): 65 75 75 75 75 75
WARNING! Before use refer to section 1. SAFETY.
4.1.
Lifting the load
Purge the hydraulic system in order to eliminate any air that may have accumulated in transit or whilst stored.
a) Place the telescopic jack lever over the release valve tang and turn anti clockwise to open the valve.
b) Insert the telescopic jack lever into the sleeve of the hydraulic pump.
c) Pump several times to ensure complete evacuation of air from the system.
d) When complete register the telescopic lever over the release valve and turn clockwise to close.
4.1.1.
Position the jack beneath the jacking point of the load to be lifted and on to an area that is solid and level.
4.1.2.
depending upon the height to be lifted, adjust the extension screw to suit.
4.1.3.
Insert the telescopic jack lever into the sleeve of the hydraulic pump until the spring catch engages. Pump the handle, full stroke
range, so that the saddle quickly reaches the load to be lifted. depress the spring catch with a screwdriver to remove.
4.1.4. observe carefully the load and jack whilst elevating to the required height.
4.1.5.
When the load is at the required height, place correctly rated stand or stands beneath the load near the jacking point.
4.1.6.
lower the load carefully and slowly on to the stand or stands. register the telescopic jack lever over the release valve and turn
anticlockwise to open the valve. remove the jack if required for access.
read the instruction
manual
Wear safety shoes
Beware crushing
hands
PBJ3_PBJ5_PBJ8_PBJ10_PBJ12_PBJ15: Issue: 2(s) - 28/05/15
Original Language Version
© Jack sealey limited
Jack saddle axis in
line (no offset load)
use wheel chocks use axle stands
