MASKING PAPER DISPENSER TROLLEY
2 X 900MM
MODEL NO:
MK67.V2
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
9
Ensure the dispenser is on a reasonably flat, level
floor before loading.
9
Be aware that the paper cutting blades are sharp,
handle with care.
8
DO NOT
use the dispenser for any purpose other
than that for which it is designed.
2. INTRODUCTION
Two roll dispenser accepts rolls up to 900mm and features
storage tray underneath dispenser unit. Automatically applies
adhesive tape to edges of masking paper. Papers and tapes
not included.
3. SPECIFICATION
Model no ................................................................. MK67.V2
Capacity ................................................2 x 900mm paper roll
4. ASSEMBLY
4.1.
To assemble the side frames compress the silver latch
button at the top of the front leg
1B
and insert the tube into
the back leg tube
1A
until they snap together. (See A in
fig.1).
4.2.
Onto each end of the two paper bars
9
slide a large
retaining washer
6
followed by a retaining spring
27
followed by a black plastic retaining ring
5
. Insert a screw
7
into the threaded block on each retaining ring.
4.3.
Attach the side frames to each end of the paper bars as shown in Fig.1 using the four black knobs
8
.
4.4.
Fit the bottom tray between the side frames and bolt it to each leg using a bolt
22
, a washer
11
and a nut
10
.
4.5.
Attach the upper paper blade
4
to the front of the frame using two bolts
22
, two washers
11
and two nuts
10.
(The upper blade has a
wider profile than the lower blade).
4.6.
Attach the lower paper cutter
3
to the front of the frame using two bolts
22
, two washers
11
and two nuts
10.
4.7.
Attach a paper spring
17
to the back edge of each paper cutter. Hook one end of the spring to the notched back corner of the metalwork
and stretch it across and hook it to the other back corner. Take care to avoid the paper cutter teeth when doing this.
4.8.
To assemble the four tape reels as shown in fig.1 take a long bolt
12
and drop a washer
11
onto it followed by a black plastic hub
21
. Slide a reel
20
over the bolt and onto the hub ensuring that it is the right way round. Retain the assembly using another
washer followed by a nut.
4.9.
After the nut has been tightened the reel should still run freely on the hub. Attach another nut to the bolt and insert the bolt through the
frame in one of the four places indicated in fig.1. Retain the assembly in place using a wing nut
28
and a washer
11
.
4.10.
Attach the top tray
23
to the side of one of the frames using two bolts
22
, two washers
11
and two nuts
10.
The nuts and washers should
be on the inside of the tray.
4.11.
Attach the hanger
25
to the side of the opposite frame at the same level as the top tray. Insert the ends of the hanger into the holes in
the side of the frame and tip the hanger forwards so that the first bend in either end of the hanger is inside each frame tube.
4.12.
The dispenser has a tubular axle which allows an axle bolt to be screwed into either end and also fixes the axle to the frame.
4.13.
Slide a washer
31
over a bolt
30
followed by a wheel
14
and another washer
31
. Position the tubular axle
13
between the two rear legs
and pass the axle bolt through the rear leg and screw it into the thread in the end of the axle. Attach the other wheel in the same way.
Tighten the axle bolts until the wheel is lightly gripped then back off slightly to allow the wheels to rotate.
Refer to
instruction
manual
Original Language Version
© Jack Sealey Limited
MK67.V2 | Issue:2 (H,F) 06/03/20
fig.1
