InstructIon MAnuAL for:
CORDLESS 30SMD LED RECHARGEABLE
PORTABLE FLOODLIGHT LITHIUM-ION
MODEL NO : LED109C
thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give
you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS
INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
Original Language Version
LED109c Issue: 1 - 15/4/13
© Jack sealey Limited
1. SAFETY
1.1. GENERAL
WARNING!
Disconnect floodlight from mains power before
performing any maintenance.
DO NOT
shine floodlight directly into your, other person’s or animal’s
eyes.
DO NOT
allow children to use the floodlight.
Maintain the floodlight in good condition.
DO NOT
use the floodlight if it is damaged.
When not in use store the floodlight in a safe, dry, childproof
location.
DO NOT
use the floodlight without the front glass shield. Avoid
touching the front glass shield as handling may reduce its
serviceable life.
DO NOT
use the floodlight without the weather seals intact.
DO NOT
use the floodlight near flammable, combustable or
explosive liquids, soilds, gases or equipment.
Maintain the floodlight in good condition. repairs must only be
undertaken by a qualified electrician
(use an authorised service
agent.)
Keep a minimun distance of 1 metre from the front of the floodlight to
the surface which is to be illuminated.
Locate the floodlight in an adequate area for its function, keep the
area clean and tidy and free from unrelated materials.
DO NOT
install the floodlight where it is likely to be knocked or hit.
WARNING!
Ensure Health and safety, local authority and general
workshop practice regulations are adhered to when using this
floodlight.
1.2. ELECTRICAL SAFETY FOR USE OF
TRANSFORMER.
USE ONLY THE SUPPLIED
TRANSFORMER
PLUG FOR CONNECTING LAMP TO THE POWER
SUPPLY.
WARNING!
It is the user’s responsibility to read, understand and
comply with the following electrical instructions:
You must ensure the risk of electric shock is minimised by the installa-
tion of appropriate safety devices. An rccB (residual current circuit
Breaker) should be incorporated in the main distribution board. We also
recommend that an rcD (residual current Device) is used with all
electrical products, particularly portable equipment which is plugged into
an electrical supply not protected by an rccB.
You must
also read and understand the following instructions
concerning electrical safety.
1.2.1.
The Electricity At Work Act 1989
requires all portable electrical
appliances, if used on business
premises, to be tested by a qualified electrician, using a Portable
Appliance tester (PAt), at least once a year.
1.2.2. The Health & Safety at Work Act 1974
makes owners of
electrical appliances responsible for the safe condition of the appliance
and the safety of the appliance operator.
If in any doubt about
electrical safety, contact a qualified electrician.
1.2.3. You must ensure that you:
Inspect the transformer plug, cable and connector for wear and
damage to ensure items are safe before connecting to the mains
power supply. If worn or damaged
DO NOT
use.
Important:
check that the voltage marked on the transformer plug
is the same as the power supply to be used.
uncoil the cable between transformer plug and lamp.
DO NOT
pull the transformer plug from the mains socket by the
lead.
DO NOT
use any other type of transformer with this product.
DO NOT
try to take the transformer plug apart.
DO NOT
use the transformer plug to power any other electrical item.
DO NOT
get the transformer plug wet, or use in wet, damp
conditions (for indoor use only).
WARNING!
NEVER
substitute a standard 13amp 3 pin plug, or any
other type of plug, for the transformer plug.
this transformer plug reduces and rectifies the mains voltage
(230 volts Ac) to
12 volts DC.
