10/14TONNE INDUSTRIAL TOE JACK
MODEL NO:
ITJ10
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
9
Regularly inspect and lubricate the jack to ensure it is in good working order and condition.
DO NOT
use the jack if damaged or a fault is
suspected - check Section 6 Troubleshooting. If necessary, immediately repair or replace damaged parts.
9
Use recommended parts only, the use of unauthorised parts may be dangerous and will invalidate your warranty.
9
Ensure the work area is clean, tidy and free from unrelated materials and has adequate lighting.
9
Use jack on level and solid ground, preferably concrete. Avoid tarmacadam since jack may sink in.
9
If being used to lift a vehicle, park the vehicle and apply hand brake. Switch off the engine and place chocks under the wheels.
9
Ensure a minimum distance of 0.5m between load and static objects such as doors, walls, etc. to allow for tilting during jacking.
9
Check lifting point is centred and stable on jack saddle (off centre loads can slip). Position jack so as to avoid operating it from
under the load.
▲
DANGER!
Use the jack for lifting only,
NOT
for supporting the lifted load. Always use adequately rated mechanical supports.
9
Keep hands etc. clear of moving parts during raising and lowering of the load.
9
Use a qualified person to lubricate and maintain the jack. Confirm that only recommended hydraulic jack oil (Sealey ref: HJO5LS) is used
during maintenance.
8
DO NOT
exceed the rated capacity of the jack and
DO NOT
operate the jack beyond its maximum pump stroke.
WARNING!
If lifting a vehicle,
DO NOT
allow the vehicle to move, or try to start the engine, when the vehicle is jacked up.
8
DO NOT
jack a vehicle if it may result in the spillage of fuel, battery acid, or other dangerous substances.
8
DO NOT
place any part of your body under load whilst it is supported by the jack. Wait until adequately rated supports have
been correctly positioned.
8
DO NOT
use jack to support extensions or cradles.
DO NOT
modify jack in any way.
DO NOT
use the jack for any other purpose other
than that for which it was designed.
8
DO NOT
adjust the safety overload valve (fig.2.D.)
9
Ensure there are no persons or obstructions beneath the load before lowering.
9
Clean and securely stow the jack with the ram in the down position.
DO NOT
leave the ram extended. Ensure stowage area is
dry.
WARNING!
Remember, it is very dangerous to go under a load supported by a jack even if additional supports are used.
WARNING!
The warnings, cautions and instructions referred to in this manual cannot cover all possible conditions and situations that
may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but must be
applied by the operator.
2.
i
INTRODUCTION
Heavy-duty, industrial quality, dual purpose toe lift bottle jack. Has a lifting capacity of 10tonne on the toe of the jack and 14tonne on the
head. Designed to lift heavy plant or machinery where there is limited ground clearance such as fork lift trucks, machine installation or for
use on construction sites. Fitted with a 280° rotating handle to enable jacking in confined spaces.
3.
i
SPECIFICATION
Model No: .....................................................................ITJ10
Lifting Capacity at Toe: .............................................. 10tonne
Lifting Capacity at Head: ........................................... 14tonne
Minimum Toe Height: ................................................... 30mm
Maximum Toe Height:................................................. 210mm
Minimum Head Height: ............................................... 320mm
Maximum Head Height: .............................................. 500mm
4. OPERATION
WARNING!
Before lifting ensure Section 1 Safety Instructions are strictly followed.
4.1.
Before using the jack, purge the hydraulic system, in order to eliminate any air that may have accumulated during transit, as follows:
a) Fit jack handle over release valve (fig.2.B) and turn anti-clockwise to open valve.
b) Insert jack handle into the sleeve (fig.2.A) and pump several times to ensure full internal lubrication and to bleed air from the system.
c) Fit jack handle back over the release valve and turn clockwise to close.
Original Language Version
© Jack Sealey Limited
Refer to
instruction
manual
Wear protective
gloves
Wear
safety footwear
ITJ10T Issue 4 (3, F) 24/07/19
