instructions for
impact driver 20v 1/4”hex drive 180Nm
- body oNly
model no:
cp20vid
thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. Safety
1.1.
GeNeral Safety
9
maintain the impact driver and battery in good condition. check moving parts alignment on a regular basis.
9
replace or repair damaged parts. use an authorised service agent and recommended parts only. unauthorised parts may be
dangerous and will invalidate the warranty.
9
ensure the impact driver is switched off before installing the battery pack.
9
Keep the impact driver and charger clean for best and safest performance.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Evaluate your working area before using the Impact Driver; e.g. ceilings, floors and enclosures may contain electrical items or water
piping.
9
ensure battery pack is correctly inserted into the impact driver handle and latched in place before attempting to switch on impact
driver.
9
Secure loose work pieces with a clamp, vice or other adequate holding device.
9
Avoid unintentional starting.
9
Wear approved safety eye protection (standard spectacles are not adequate).
9
maintain correct balance and footing. ensure the floor is not slippery and wear non-skid shoes.
9
Keep direction switch in the locked position until the impact driver
is required for use.
9
Keep children and unauthorised persons away from the working area.
8
do Not
use the Impact Driver where there are flammable liquids, solids or gases, such as paint solvents, etc.
8
do Not
allow children to operate the impact driver.
8
do Not
operate the impact driver
if any parts are missing as this may cause failure and/or personal injury.
8
do Not
hold unsecured work piece in your hand.
8
do Not
leave the impact driver operating unattended.
8
do Not
carry the impact driver with your finger on the power switch. Keep chuck direction switch in the locked position.
8
do Not
use the impact driver for a task it is not designed to perform.
8
do Not
operate the impact driver
when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
do Not
get the impact driver or battery charger wet or use in damp or wet locations.
2. iNtroductioN
t
he 20V series has been designed to suit users from the DIY enthusiast to the professional. These body only tools offer a one battery fits all
solution with a choice of 20V lithium batteries ranging from 2Ah to 4Ah, meaning costs can be kept down whilst quality remains high. Quality,
stylish, lightweight tools with composite housing and a soft grip making them comfortable and easy to use.
3. SpecificatioN
model no.. ............................................................... cP20Vid
Battery ............................
20V 2Ah - 4Ah Li-ion (not included)
drive ........................................................................
1/4” Hex.
impact rate ........................................................... 0-3000bpm
no load speed ......................................................0-2200rpm
m
aximum Torque
.........................................................180nm
Battery model no’s
2Ah ..................................................................... cP20VBP2
3Ah ...................................................................... cP20VBP3
4Ah ...................................................................... cP20VBP4
mains charger model no ...................................... cP20Vmc
Weight ......................................................................... 1.17kg
noise power .................................................................106dB
noise pressure ...............................................................95dB
Vibration ................................................................. 15.87m/s²
uncertainty ................................................................. 1.5m/s²
cP20Vid | issue 1 06/04/18
Original Language Version
© Jack sealey limited
refer to
instructions
Wear eye
protection
Wear protective
gloves
Wear ear
protection
