background image

HAMMER DRILL/DRIVER 20V 13MM - BODY 

ONLY

MODEL NO: 

CP20VDD

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, 

and properly maintained, give you years of trouble free performance.

IMPORTANT:

 PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE 

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR 
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1.  SAFETY

1.1.   GENERAL SAFETY

 

9

   Disconnect the drill from the battery unit before changing accessories, servicing or performing any maintenance.

 

9

   Maintain the drill and battery in good condition. Check moving parts alignment on a regular basis. 

 

9

   Replace or repair damaged parts. Use an authorised service agent and recommended parts only. Unauthorised parts may be  

 

  dangerous and will invalidate the warranty.

 

9

   Ensure the drill is switched off before installing the battery pack.

 

9

   Keep the drill and charger clean for best and safest performance.

 

9

   Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.

 

9

   Evaluate your working area before using the drill e.g. ceilings, floors and enclosures may contain electrical items or water piping. 

 

9

   Ensure battery pack is correctly inserted into the drill handle and latched in place before attempting to switch on drill.

 

9

   Secure loose work pieces with a clamp, vice or other adequate holding device. 

 

9

   Avoid unintentional starting.

 

9

   Wear approved safety eye protection (standard spectacles are not adequate).

 

9

   Maintain correct balance and footing. Ensure the floor is not slippery and wear non-skid shoes.

 

9

   Keep chuck direction switch in the locked position until the drill is required for use.

 

9

   Keep children and unauthorised persons away from the working area.

 

9

   Keep drill and charger in the case and store in a safe, dry, childproof area where the temperature will not exceed 104°F (40°C).

 

8

  

DO NOT

 use the drill where there are flammable liquids, solids or gases, such as paint solvents, etc.

 

8

  

DO NOT

 allow children to operate the drill.

 

8

  

DO NOT

 operate the drill if any parts are missing as this may cause failure and/or personal injury.

 

8

  

DO NOT

 hold unsecured work piece in your hand.

 

8

  

DO NOT

 leave the drill operating unattended.

 

8

  

DO NOT

 carry the drill with your finger on the power switch. Keep chuck direction switch in the locked position.

 

8

  

DO NOT

 use the drill for a task it is not designed to perform.

 

8

  

DO NOT

 operate the drill when you are tired or under the influence of alcohol, drugs or intoxicating medication.

 

8

  

DO NOT

 get the drill or battery charger wet or use in damp or wet locations. 

2. 

INTRODUCTION

 

Powerful, lightweight cordless drill/driver with hammer function. Comfortable composite housing with soft grip for added comfort. 2-13mm  

 

keyless chuck. Three drill functions and 18 torque settings provide the control required to complete various tasks. Built in LED work light.  

 

Forward, reverse and trigger lock. Supplied with belt hook for safer storage whilst not in use. Requires battery model no’s CP20VBP2,  

 

CP20VBP or CP20VBP4 20V Battery and Model No. CP20VMC Mains Charger.

3. 

SPECIFICATION

Model No:  .............................................................CP20VDD

No Load Speed: .................................................... 1250 RPM

Impact Rate: ...................................

0-6000bpm/0-22500bpm

Drilling Capacities:

Chuck Size: ...............................................................

Ø13mm

Wood: .......................................................................

Ø35mm

Metal: ........................................................................

Ø13mm

Concrete: ..................................................................

Ø13mm

Maximum Torque:..........................................................

35Nm

Noise Power..............................................................

96.57dB

Noise Pressure .........................................................

85.57dB

Vibration .................................................................

2.546m/s

2

Uncertainty ................................................................. 1.5m/s

2

Weight: ........................................................................ 1.25kg

Original Language Version

© Jack Sealey Limited

Refer to 

instruction

manual

Wear eye 

protection

Wear a

mask

Wear ear 

protection

Wear protective 

gloves

    CP20VDD     Issue 2  (3, 4)   08/05/18

Reviews: