![background image](http://html.mh-extra.com/html/sealey/adb300/adb300_instructions_1224278001.webp)
INSTRUCTIONS FOR:
AIR DRYER/BLOWER
MODELS: ADB300, ADB3000
Thank you for purchasing a Sealey Air Dryer/Blower. Manufactured to a high standard this product will, if used according to these
instructions and properly maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE
AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.1.
PLUG & MAINS POWER SUPPLY
!
WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any
other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety
devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend that a
Residual Current Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into a supply which is
not protected by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey
dealer.
You must
also read and understand the following instructions concerning electrical safety.
1.1.1. The
Electricity at Work Act 1989
requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The
Health & Safety at Work Act 1974
makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators.
If in any doubt about electrical safety, contact a
qualified electrician.
1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the
power supply. See 1.1.1. and 1.1.2. and use a Portable Appliance Tester.
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check all connections
to ensure that none is loose.
1.1.6.
Important:
Ensure that the voltage marked on the appliance matches the power supply to be
used and that the plug is fitted with the correct fuse - see fuse rating on right.
1.1.7.
DO NOT
pull or carry the appliance by the power cable.
1.1.8.
DO NOT
pull the plug from the socket by the cable.
1.1.9.
DO NOT
use worn or damaged cables, plugs or connectors. Immediately have any faulty item
repaired or replaced by a qualified electrician. When an ASTA/BS approved UK 3 pin 13 amp
plug is damaged, cut the cable just above the plug and
dispose of the plug safely.
Fit a new plug
according to the following instructions (UK only - see diagrams on right).
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer
insulation extends beyond the cable restraint and that the restraint is tight.
1.1.10. If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any appliance plugged
into it will be protected. The cable core section is important and should be at least 1.5mm
2
, but to be absolutely sure that the capacity of
the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use of 2.5mm
2
section cable.
Blue
Neutral
Wire
Yellow & Green
Earth Wire
Cable
Restraint
Brown
Live
Wire
FUSE RATING 13 AMP
ADB300, ADB3000 - 1 - 190106
1.2. GENERAL SAFETY
!
WARNING!
Disconnect air dryer/blower from mains supply when not in use, before servicing or performing any maintenance.
!
WARNING!
If the air dryer/blower falls into water or other liquid, immediately switch off and disconnect from the mains power supply. Do not
touch the unit until the mains power supply has been disconnected.
#
Always disconnect the air dryer/blower from the power supply when moving it from one location to another and ensure that it is stood on a level surface.
#
Before using ensure there are no materials or items that may be blown about by the stream of air.
Mandatory min. distance from the unit is 1mtr.
$
DO NOT obstruct the air inlet and outlet sections of the air dryer/blower.
#
Keep the air dryer/blower clean and maintained in good condition. For electrical components or motor service contact an authorised service
agent. Replace or repair damaged parts. Use recommended parts only (unauthorised parts may be dangerous, and will invalidate your warranty).
%
DO NOT operate the air dryer/blower where there are harmful, explosive or flammable gases, fumes or hazardous substances.
%
DO NOT stand the air dryer/blower on the electrical power cable.
%
DO NOT insert objects through any of the air dryer/blower grilles.
%
DO NOT modify speed control or attempt to fit any additional external speed control device to the fan.
%
DO NOT cover the air dryer/blower when in use.
%
DO NOT allow children to operate the air dryer/blower.
%
DO NOT stand the air dryer/blower where it may be knocked over or off a surface, or where the lead may cause a person to trip.
%
DO NOT use the air dryer/blower outdoors.
#
When not in use place the air dryer/blower in its original box, or cover the unit to protect from dust, and store in a safe, dry, childproof location.
.