background image

INSTRUCTIONS FOR:

TROLLEY JACK  

Model: 

1

1

0

0

0

0

2

2

.

.

V

V

2

2

1002.V2

Note: Numbers in brackets refer to item numbers shown in the Parts List.

3.1. Fit the handle (89) to the pumping handle (7) and retain with screw (90) and nut (91).

3.2. Place the pumping handle (7) in the tipping gear (6) and screw the locking screw (18) completely into the locking slot in the handle.

(IT IS VERY IMPORTANT YOU CHECK THAT THE SCREW IS ENGAGED INTO THE SLOT.)

3.3. Oil the mechanical parts before first use - and regularly thereafter.

3.4. Before using for the first time open the release valve and pump the handle for 30-40 seconds. Close the release valve. This will 

purge any air in the hydraulic system. Jack is now ready for use.

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions 

and properly maintained, give you years of trouble free performance.

IMPORTANT:

READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.

USE THIS JACK CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE

DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. RETAIN THESE INSTRUCTIONS FOR FUTURE USE.

1.  SAFETY PRECAUTIONS

3. ASSEMBLY & PURGING 

2. SPECIFICATION

Capacity   . . . . . . . . . . . . . . . . . . .10000kg 

Min. Saddle Height   . . . . . . . . . . . .195mm 

Max. Saddle Height  . . . . . . . . . . . .650mm

Max. Chassis Height  . . . . . . . . . . .280mm  

Length  . . . . . . . . . . . . . . . . . . . . .1550mm 

Weight  . . . . . . . . . . . . . . . . . . . . . . .145kg

3

Ensure that the jack is in sound condition and good working order. Take action for immediate repair or replacement of damaged parts. 

Use genuine parts only. The use of unauthorised parts may be dangerous and will invalidate the warranty.

3

Locate the jack in a suitable, well lit work area.

3

Keep work area clean and tidy and free from unrelated materials.

3

Use jack on level and solid ground, preferably concrete. 

Avoid tarmacadam as jack may sink in

.

3

Place wedges under wheels of vehicle (

but ensure wheels of jack can move freely).

3

Ensure the vehicle handbrake is engaged, engine is switched off and transmission is in 1st or reverse gear (“Park” if automatic).

3

Ensure minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc., to allow for vehicle tilting during lifting.

3

Ensure that there are no passengers in the vehicle.

3

Ensure that all non-essential persons keep a safe distance whilst the jack is in use.

3

Only place jack under those lifting points recommended by vehicle manufacturer

(see vehicle handbook).

3

Check the lifting point is stable and centred on the jack saddle.

3

Ensure that the jack wheels are free to move and that there are no obstructions.

DANGER: 

Use the jack for lifting only, 

NOT

for supporting the lifted load.

3

Use suitable capacity axle stands under the vehicle before proceeding with any task.

3

Ensure that there are no persons or obstructions beneath the vehicle before lowering.

3

Use a qualified person to maintain or repair the jack hydraulic system.

7

DO NOT

operate the jack if it is damaged.

7

DO NOT

allow untrained persons to operate the jack.

7

DO NOT

exceed the rated capacity of the jack.

7

DO NOT

allow the vehicle to move while supported by the jack and 

DO NOT

use the jack to move the vehicle.

7

DO NOT

jack vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substances.

7

DO NOT

work under the vehicle until suitable axle stands have been correctly positioned.

7

DO NOT

use the jack for purposes other than that for which it is designed.

7

DO NOT

top up hydraulic system with brake fluid. Use hydraulic jack oil only.

7

DO NOT

adjust the safety overload valve.

3

When not in use store jack, fully lowered, in a safe, dry, childproof area.

p

p

 

 

 

 

p  

WARNING!

It is 

very dangerous

to go under a vehicle which is supported by a jack 

even

if additional supports are used. 

DO NOT

go under 

a vehicle unless it is supported by adequately rated axle stands.

s

s

 

 

IMPORTANT! Ensure you can see the saddle and jacking point throughout the jacking operation in case there is any relative movement.

4. OPERATING INSTRUCTIONS

4.1. General jacking

p

p

p

WARNING! Before lifting, ensure Section 1 safety instructions are strictly followed. 

4.1.1. Prepare vehicle as described in safety instructions, ensuring that the ground on which jack is to stand is level and solid (not tarmacadam).

4.1.2. Position the jack saddle under the vehicle manufacturer’s recommended lifting point (see vehicle handbook).

4.2. Jacking the vehicle

4.2.1. Lift and lower the pumping handle or the quick-lift pedal over the entire arc of operation until the saddle reaches the lifting point. Then pump

the handle to raise the vehicle.

Note:

If the jack becomes overloaded, the safety valve will operate and prevent the jack from lifting further.

4.3. Lowering the vehicle 

4.3.1. Pull the handle up and turn it clockwise.

SAFETY WARNING!

Always lower in a slow and controlled manner and ensure that there are no persons or obstacles beneath the 

vehicle, or in the path of descent.

1002.V2  - 1 - 020502

Reviews: