SDC CL600 Series Installation Instructions Manual Download

Page: 1 / 11

Home (/) > Knowledge Base - Home (/knowledgebase/) > KA-01080

CL600 - Installation Instructions



Contents

Check that the contents of your box are correct according to the model.

Model 600/605 Model 610/615 Model 620/625

1 Front plate and handle

2 Back plate and handle

3 Neoprene seals x 2

4 RED & BLUE tipped spindles

5 Fixing bolts x 4 (1 x spare)

6 Front plate cylinder cover

7 Allen keys x 2

8 Euro profile cylinder escutcheons

1 pair

8a Keyhole escutcheons

1 pair

9 Mortice latch, strike & 4 screws

10 2 bolt mortice lock and strike

11 Double Europrofile cylinder & 3 keys -

12 Code change keys

Adaptor kit for mortice locks
with horizontal fixings

14 Latch support post

15 Code change tool

Installation template

Code change instructions

Code card

Fire Kit (optional)

(See page 13) -

Tools Required for installation:

• Power drill

• Drill bits 30mm (1 ⁄ "), 25mm (1"), 20mm ( ⁄ "), 16mm ( ⁄ ") & 10mm ( ⁄ ")

• Phillips screwdriver

• Chisel - 22mm ( ⁄ ")

• Chisel - 25mm (1")

• Hammer/Mallet

• Stanley knife

• Adhesive tape

• Pencil

• Bradawl

• Tape measure

Summary of Contents for CL600 Series












Search results

Summary of Contents for CL600 Series

Reviews:

Related manuals for CL600 Series

Brands by name

Popular brands

SDC CL600 Series, Installation Instructions Manual

Search results

Summary of Contents for CL600 Series

Reviews:

Related manuals for CL600 Series

Brands by name

Popular brands