Schwank STR Series Installation & Owner'S Manual Download | Manualshive

Page: 1 / 33

background image

SP-MSTR-AC-11A

STR Manual

RD: NOV, 2003

RL: 11

KH

INSTALLATION /
OWNER’S
MANUAL

SCHWANK GAS FIRED

STR

SERIES

LOW INTENSITY, TUBE-TYPE

INFRA RED HEATERS

FOR YOUR SAFETY:

Do not store or use gasoline or other flammable
vapours and liquids in the vicinity of this or any
other appliance.
If you smell Gas:
>Extinguish any open flames
>Don’t touch electrical switches
>Call your Gas supplier immediately

FIELD CONVERTIBILITY:

“The conversion shall be carried out in
accordance with the requirements of the
authorities having jurisdiction and in
accordance with the requirements of the B149.1
(latest edition) INSTALLATION CODE” in
Canada, and the ANSI Z223.1 (latest edition) in
the U.S.A

FOR YOUR SAFETY

If you smell gas:
(1) Open windows
(2) Don’t touch electrical switches
(3) (Extinguish any open flame

Immediately call your gas supplier

1
2
3
...
»

Summary of Contents for STR Series


































Reviews:

No comments

Related manuals for STR Series

Zoneline AZ85H09DAC

Brand: GE Pages: 2

Brand: GE Pages: 2

Brand: Water Worker Pages: 24

Brand: Laars Pages: 68

Brand: L.B. White Pages: 99

Brand: Napoleon Pages: 20

Brand: Napoleon Pages: 40

GQ-C3257WX-FF US

Brand: Noritz Pages: 47

Brand: Ferret Pages: 8

Brand: Rheem Pages: 48

Brand: Trane Pages: 8

Brand: Viessmann Pages: 52

Brand: iGenix Pages: 9

Brand: Chromalox Pages: 4

Brand: Nectre Fireplaces Pages: 10

Brand: York Pages: 24

Brand: Zibro Pages: 24

POWER VENTED GAS FIRED WATER HEATER

Brand: GSW Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands