background image

 

 
 
Important Safety Instructions 

1. 

Please read these instructions thoroughly. 

2. 

Please keep this guide for future use. 

3. 

Please disconnect the device from the main supply before cleaning. Do not use any liquid or 
aerosol spray cleaners. The best for cleaning is a piece of cloth dampened with water. 

4.  To avoid damage of the device, you should only use accessory parts permitted by the 

manufacturer. 

5. 

The device must be protected against moisture. 

6. 

To setup the device, it must be put in a stable stand position. Tipping it over or dropping it may 
cause injuries. Only use safety setup locations and follow the setup instructions of the 
manufacturer. 

7.  The ventilation openings are used for air circulation which protect the device against 

overheating. 

8. 

To connect the device, follow the connected load values of the main supply. 

9. 

Due to electrical safety, the wall socket must be equipped with a non-fused earthed conductor 
contact. 

10.  The power cable must be laid in a way that nobody may trip over it. There should also nothing 

be resting on the cable. 

11.  All instructions and warning remarks on the device must be followed. 
12.  If the device will not be used for a long period of time, you should disconnect it from the main 

supply to avoid overvoltage damage. 

13.  Any objects or liquid should never enter the device via its openings for air circulation. This 

could cause a fire or an electric shock. 

14.  Do not open the device ever. For electrical safety, the device shall be opened by  authorized 

technical service personnel only. 

15.  If following conditions occur, the device must be disconnected from the main supply, and it 

must be checked by a qualified service center: 

a- 

Power cable or power plug are damaged; 

b- 

Liquid has entered the device; 

c- 

The device was exposed to moisture; 

d- 

The device does not operate according to the user's guide, or you do not achieve any im-

provement with the aid of this guide; 

e- 

The device has dropped and/or the casing is damaged; 

f- 

The device shows obvious signs of a defect. 

16.  For repair, only original spare parts or parts in accordance with the original parts may be used. 

Use of unsuitable spare parts can cause more damage. 

17.  Please turn to your service center for all questions concerning service and repair to guarantee the 

device's performance reliability. 

18.  The socket outlet must be installed near the equipment to be easily accessible. 

 

Summary of Contents for D73P





















Reviews: