background image

®

 

MSD-300 

WIRELESS SMOKE AND HEAT DETECTOR 

msd300_en 10/11 

The MSD-300 multisensor detector can detect the early stages of fire development when 
there is some visible smoke and/or temperature rise. It can operate as a stand-alone device 
or in combination with the MICRA alarm module. This manual applies to the detector with 
electronics version 1.1 or later. 

1. Features 

  EN54-7 compliant visible smoke sensor. 

  EN54-5 compliant heat sensor. 

  Red LED for optical signaling. 

 Built-in 

sounder. 

 Test 

feature. 

  Tamper switch (supervised when working in the MICRA system). 

2. Functional description 

An optical method is used for the detection of visible smoke. When the concentration of 
smoke in the optical chamber exceeds a given threshold, an alarm is triggered. The smoke 
sensor operating parameters are modified depending on the temperature changes recorded 
by the heat sensor (thermistor). 
The heat sensor operates according to the requirements of Class A1R (EN 54-5). The alarm 
will be triggered after exceeding a certain threshold temperature (54°C - 65°C) or in the event 
when the temperature rises too rapidly (see Table 1). 
 

Air temperature rise 

velocity 

Lower limit of response 

time 

Upper limit of response 

time 

1 °C/min 

29 min 

40 min 20 s 

3 °C/min 

7 min 13 s 

13 min 40 s 

5 °C/min 

4 min 9 s 

8 min 20 s 

10 °C/min 

1 min 

4 min 20 s 

20 °C/min 

30 s 

2 min 20 s 

30 °C/min 

20 s 

1 min 40 s 

Table 1. Response time limits for the heat sensor. 

 
The alarm is indicated visually (LED steady light) and acoustically (intermittent sound) for 2 
minutes. Pressing the test / reset button (designated with the letter A in Figure 1) during the 
alarm will clear the alarm condition. The alarm information is sent by radio to the MICRA 
alarm module. After the alarm causes cease to exist, information about the alarm end will be 
sent. 
Every 15 minutes, the detector sends a transmission containing information on tamper 
contact and battery status. Periodic transmissions are used to monitor the presence and 
operation of the detector by the MICRA module. 

alarm shop

Summary of Contents for MSD-300

Page 1: ...cording to the requirements of Class A1R EN 54 5 The alarm will be triggered after exceeding a certain threshold temperature 54 C 65 C or in the event when the temperature rises too rapidly see Table 1 Air temperature rise velocity Lower limit of response time Upper limit of response time 1 C min 29 min 40 min 20 s 3 C min 7 min 13 s 13 min 40 s 5 C min 4 min 9 s 8 min 20 s 10 C min 1 min 4 min 20...

Page 2: ...erent mounting location and repeat the test 7 Using wall plugs screw anchors and screws fasten the enclosure base to the ceiling 8 Close the detector enclosure 9 Press and hold down the test reset button designated with the letter A in Figure 1 to make sure that the detector works Alarm should be triggered after a few seconds 10 If any other operations which may cause contamination of the optical ...

Page 3: ...n the respective grooves 11 Replace the thermistor cover 12 Secure the electronics board with the optical chamber in the cover mounting catches The board must be mounted so that the LED coincides with the light guide button 13 Re install the battery 14 Close the detector enclosure alarm shop ...

Page 4: ...ton designated with the letter A in Figure 1 to make sure that the detector works Alarm should be triggered after a few seconds 6 Specifications Operating frequency band 433 05 434 79 MHz Radio communication range in open area up to 200 m Battery CR123A 3 V Battery life expectancy approx 3 years Standby current consumption 50 µA Maximum current consumption 20 mA Class according to EN 54 5 heat sen...

Reviews: