![background image](http://html.mh-extra.com/html/sargent/assa-abloy-3727-series/assa-abloy-3727-series_instructions-for-installing_1199077001.webp)
A7425F
CAUTION: BEFORE STARTING
• DOOR SHOULD BE FITTED AND HUNG
• CHECK BOX LABEL FOR HAND AND SIZE OF EXIT DEVICE
AVAILABLE STOCK LENGTHS
LENGTH E
32" DOOR. CAN BE CUT TO FIT 24" DOOR.
LENGTH F
36" DOOR. CAN BE CUT TO FIT 30" DOOR.
LENGTH G
48" DOOR. CAN BE CUT TO FIT 36" DOOR.
Lift
lever
Lift
lever
pin
2-1/4" long pin
Top case
Rail assembly
Top rod
Guide
Guide
Bottom
rod
Adjustment
pin
Bottom
case
Vertical reference line
(CL of chassis)
Vertical reference line
(CL of chassis)
Horizontal reference line
(CL of chassis and rail assembly)
Horizontal reference line
(CL of chassis and rail assembly)
Horizontal reference line
(CL of chassis and rail assembly)
Vertical reference line
(CL of chassis)
US PATENT NO. 268003
CANADIAN PATENT NO. RD1981
ALL 3727 SERIES EXIT DEVICES
ARE HANDED AND REVERSIBLE. NORMALLY ASSEMBLED FOR
A LEFT HAND REVERSE BEVEL DOOR AT THE FACTORY.
TO CHANGE HAND OF 3727 EXIT DEVICE:
1. USE 2-1/4" PIN (SUPPLIED IN SCREW PACK) TO PUSH OUT
LIFT LEVER PIN.
2. REMOVE LIFT LEVER. INVERT AND REASSEMBLE WITH LIFT
LEVER PIN AS SHOWN.
THIS EXIT DEVICE IS HANDED
Door stop
Top case
template
TAPE TEMPLATES ON INSIDE OF DOOR ALONG
REFERENCE LINES WITH SUPPLIED TAPE
IF DOOR ALREADY HAS ANSI DOOR PREP (161 CUT-OUT) OR HAS
2-1/8" DIA. HOLE AT 2-3/4" BACKSET, POSITION TEMPLATE OVER EXISTING
HOLE AND SPOT AND DRILL HOLES
1.
DETERMINE DIMENSION “A”
- IF LOCK STILE IS APPROX. 4-1/2"
WIDE OR WIDER, DIM. A = 2-3/4"
- IF LOCK STILE IS LESS THAN 4-1/2"
WIDE, DIM. A = 1/2 OF THE VISIBLE
WIDTH OF THE LOCK STILE (WHEN
DOOR IS CLOSED AGAINST STOP)
FINISHED FLOOR
Refer to template to locate
horizontal reference line
RIGHT HAND
REVERSE BEVEL
LEFT HAND
REVERSE BEVEL
OUT
Bottom
cover
Center chassis
assembly
Top cover
Adjustment pin
Lockdown
button
“Lockdown key”
To operate:
Depress pushrail; insert hex key
and turn
Mounting plate
End cap
Door
Dim “A”
2.
PREPARE DOOR
3.
APPLY HARDWARE
ANSI A156.2 series cross bore hole
when knob rim or lever handle trim
is used
FOR LEVER TRIM APPLICATIONS
SEE SEPARATE INSTRUCTION SHEET PACKED WITH TRIM
41”
INSTRUCTIONS FOR INSTALLING
3727 / NB3727 SERIES
VERTICAL ROD EXIT DEVICE
FOR ASSISTANCE, CONTACT SARGENT AT 800-727-5477 or www.sargentlock.com
Copyright © 2003, 2008, 2012, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
NOTE: FOR EXIT APPLICATIONS ONLY
REMOVE AND DISCARD CAM FROM
CENTER CHASSIS FOR FLUSH
MOUNTING. ATTACH CHASSIS WITH
FOUR (4) #10 WOOD OR MACHINE
SCREWS.
Cam
Center
chassis
cam
MARK VERTICAL AND HORIZONTAL
REFERENCE LINES ON DOOR