background image

PRECAUTIONS

PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO

EXCESSIVE MICROWAVE ENERGY

(a)   Do not operate or allow the oven to be operated with the door open.
(b)   Make the following safety checks on all ovens to be serviced before activating the magnetron or other
       microwave source, and make repairs as necessary:
       (1)Interlock operation, (2) proper door closing, (3) seal and sealing surfaces (arcing, wear, and other
       damage), (4) damage to or loosening of hinges and latches, (5) evidence of dropping or abuse.
(c)   Before turning on microwave power for any service test or inspection within the microwave generating
       compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment,
       integrity, and connections.
(d)   Any defective or misadjusted components in the interlock, monitor, door seal, and microwave generation

and transmission systems shall be repaired replaced, or adjusted by procedures described in this manual
before the oven is released to the owner.

  SERVICE MANUAL      

Microwave Oven

EM-C1800MK

(Germany)

EM-C1800MK

(U.K)

REFERENCE NO.

 

SM-640177

Model No               Pro.Code No

EM-C1800MKSD    437 477 00

EM-C1800MKUK    437 477 01

Foreword

    

 Read this manual carefully, especially precaution on microwave energy, and follow the procedure strictly,

         careless servicing and testing may expose yourself to the microwave energy leakage.

Summary of Contents for EM-C1800MK

























Reviews: