background image

Sanuvox Technologies Inc, © 2020 All rights reserved. November 2020 EN v.5

Instruction Manual

Photos illustrating products are non contractual.

SANUVAIR

®

 S100

GX

AIR 

SANITIZER 

PURIFICATIO

N

 UNIT

Commercial Model

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE SAFETY INSTRUCTIONS BEFORE USING THIS PRODUCT.

Read and follow all instructions contained in 

this manual before using the product. Read the 

maintenance instructions before opening the unit. 

Failure to comply with these instructions may result 

in personal injuries or damage to the unit or system.

1. Installation and servicing of air conditioning and

related equipment can be hazardous due to systems 

pressure and electrical components. Only trained

and  qualified  service  personnel

 should install,

repair or service equipment.

2. Untrained personnel can perform basic 

maintenance functions such as replacing lamp(s)

and/or  filter(s).  All  other  operations  should  be 

performed by trained service personnel.

3. The  unit  is  not  to  be  used  by  persons  (including 

children) with reduced physical, sensory or mental

capabilities,  or  lack  of  experience  and  knowledge, 

unless they have been given supervision or instruction.

CAUTION: Unit is not a toy. Do not leave children

unattended with the unit.

4. Units  that  are  obviously  damaged  must  not  be 

operated.

5. When  working  on  the  unit  or  system,  observe 

precautions in the literature, tags and labels attached 

to the unit or system, and all other safety precautions

considered as best practices in the HVAC industry.

6. When  applicable,  local  regulation  may  comprise 

more  restrictive  installation  and/or  certification 

requirements. The afore mentioned requirements

prevail on those of this document and the installer

agrees to conform to these at his own expense.

7. Follow all the safety instructions outlined in this

document and respect all local and national codes

applicable.

8.  This  unit  contains  a  UV-C  emitter.  Unintended  use  of 

the unit or damage to the housing may result in harmful

UV-C radiation leaks. UV-C radiation may, even in little 

doses, cause harm to the eyes and skin.

9. Never expose eyes or skin to ultraviolet light

from any source. Therefore, before installing or

performing maintenance on the unit or system,

TURN OFF AND DISCONNECT the unit or system

from all power sources

  (there  may  be  more  than 

one switch to disconnect).

CAUTION:

 Electrical shock may cause personal 

injuries or possibly death.

10. UV rays may destroy certain types of filters (polymer 

or plastic); please keep the unit or system light away 

from shining directly on plastic.

11. When installing or performing maintenance on the

UV unit or system, it is recommended to 

wear safety

glasses and gloves. In order to avoid reduced

performance of lamp(s), do not touch lamp glass

without gloves.

12. UV  lamps  contain  a  small  quantity  of  mercury:  if  a 

lamp  breaks,  clean  and 

dispose of with care

.  UV 

lamps  can  be  disposed/recycled  after  use,  as  any 

other fluorescent lamps. Contact and follow your local 

and national authorities’ specific instructions.

13.

Use  only  specified  SANUVOX  branded 

replacement UV lamps with your unit or system.

Use of any other lamps will void your warranty and

can result in damage to the unit, system and/or

lamp(s).

14. Most UV units or systems are not waterproof. 

DO NOT 

INSTALL OUTDOORS

 unless specified otherwise.

SAVE THESE INSTRUCTIONS

Installation Date:  _______________   Installed by:  _________________
Installer Contact Info.:  _________________________________________

REGISTER 

YOUR WARRANTY

 

ONLINE AT 

www.sanuvox.com

Summary of Contents for SANUVAIR S100GX













Reviews: