![background image](http://html1.mh-extra.com/html/salto/la1t05-series/la1t05-series_installation-manual_3680664001.webp)
P-221378 - ED3. 10/09/2020
Installation guide
SALTO LA1T
0
5xx/LA1T
1
5xx
/LA1T
3
5xx mortise locks for AACC
Hand changing
Changement de main
Cambio de mano
F
E
Eng
F
Installation guide
Guide d'installation
Guía de instalación
Eng
E
TORX 10
4-3/8"
( 110 )
1-5/8"
( 41,2 )
q
5/16"
(
q
8 )
1-1/2"
( 38,1 )
6-1/8"
( 156 )
2-3/4"
( 70 )
27/64"
( 10,7 )
3/4"
( 19 )
1-1/16" ( 26,5 )
LA1T15xx.. mod.
8"
( 203 )
1-1/16" ( 27 )
1-1/4" ( 32 )
LA1T15xx.. mod.
LA1T05xx..
LA1T15xx..
4
1
2
3
5
6
ANSI handing code
ANSI code de remise
Código mano ANSI
F
E
Eng
LA1T35xx.. mod.
LA1T35xx.. mod.
9/32" ( 7,1 )
LA1T35xx..
AUTOMATIC
Adjustment screw
Vis d´ajustement
Tornillo de ajuste
Pivot lock front
Têtière pivotante
Frente pivotante
Top of Lock
Latèral de la mort
Lateral de la cerra
Adjust bevel
Ajustement de la têtiere
Adjuste del frente
F
E
Eng
RH
LH
PREPARING THE DOOR
Note: if the strike already exists in the door frame, position lock using strike as reference (See strike position on template)
1.
Draw horizontal line on both sides and edge of door at the desired height of knob above floor.
2.
Draw vertical center line on door edge.
3.
Draw vertical line on each side at the proper backset to align the template.
4.
Position templates on edge and sides of door.
Mark holes ONLY for each side, and top and bottom holes of mortise cavity on door edge, and holes in the lateral face of the door for
handles, turn piece hole (only needed in inside face).
5.
If lock has anti-friction latch, mark proper recess area on door edge template. (See lock body to determine proper side.)
6.
Remove template: place lock face against door edge.
Trace outline of faceplate as guide for faceplate routing.
MORTISE THE DOOR
1.
Mortise door for lock body and faceplate per instructions on template.
INSTALLING THE LOCK BODY
1.
Insert the lock into the cavity.
2.
Mark & drill faceplate holes. Fasten with faceplate screws to hold lock in place.
3.
For locks with door detector, see 201082 installation guide to connect.
INSTALLING THE STRIKE
1.
Refer to template to determine strike location on jamb.
2.
Using strike as template, mark and chisel recess.
Drill screw holes and fasten.
3.
Gap between door and jamb is between
3/32” and 7/32”
.
ADJUST BEVEL
1.
Loosen adjustment screws at top and bottom of case.
2.
Turn front to desired bevel.
3.
Re-tighten adjustment screws.
NOTE:
Holes for the fixation of the SALTO electronic escutcheon are not included in this template. Please use the template included in the escutcheon box.
Door code
Mortise code
LH
RHR
RH
LHR
L
R
HE
IGH
T
AB
OV
E F
L
OO
R
OF
LEVER
OF
DOOR
EDGE
L
C
L
C
L
C
L
C
OF
LEVER
OF
BASKSET
Installation
Installation
Instalación
E
Eng
F
Eng
ANSI A156.13 Grade 1