background image

MICROWAVE SMS830 MOTION SENSOR product electrical and installation specification effective 

8

/

8

/2023.

 

SAL National Pty Ltd. 40 Biloela Street Villawood NSW 2163 ABN 21 633 189 474

Copyright SAL V16 JUL 2021  |  

www.sal.net.au  

 |  Page 1 of 3

IMPORTANT: IN THE INTEREST OF PRODUCT PERFORMANCE AND SAFETY PLEASE READ THESE INSTALLATION AND WARRANTY INSTRUCTIONS BEFORE INSTALLING THE PRODUCT.

MUST BE INSTALLED

BY A LICENSED

ELECTRICIAN

DIY

SAL products are designed in accordance with all mandatory International and AS/NZS Standards, which require installation in 
accordance with AS/NZS3000 by a qualified installer and regular cleaning and maintenance of the equipment. Products are 
sold in accordance with the following instructions and SAL standard terms and conditions of sale, available via www.sal.net.au.  

Due to continued product and information updates, product data sourced from sal.net.au shall not form part of any contract and or technical performance 

guarantee unless expressly confirmed in writing by SAL at the time of order.

General product application requirements (if applicable) :

1. CCT or POWER selections (where supplied) – IMPORTANT, where CCT colour temperature or POWER selection switching is provided, it is important to switch OFF the 
power before the selection is made, otherwise equipment damage may occur.

2. Recycling – SAL encourages recycling, please consider the environment when disposing of packaging, batteries & components.

3. Switching or test intervals  For optimum product performance, good design practice does not encourage 24/7 operation of lighting products without the provision 
of a routine switching or regulatory test cycle. As a guide for continual operation installations, a twelve (12) hour duration for Industrial and Commercial applications 
and a six (6) hour duration for Residential applications should be considered.

4.  Product maintenance – In line with the relevant design standards and to protect your investment, it is important to have in place a routine cleaning program that
reflects the installation environment and maintains the product in a clean and functional condition.

IMPORTANT - The supply must be isolated before any product maintenance or cleaning is conducted. In addition, damage to ANY cable or cord supplied with the 
product must be addressed as follows; For attachment type X having a specially prepared cable, if the external flexible cable is damaged, it must be replaced by an 
equivalent cable exclusively available from the manufacturer or authorised installer. For attachment type Y, if the external flexible cable is damaged, it must be 
exclusively replaced by an equivalent cable by the manufacturer or authorised installer. For attachment type Z, if the external flexible cable is damaged, the cable 
cannot be replaced and the luminaire must be destroyed.

5.  Adverse, corrosive and coastal installation environments  Unless the product is specifically designated for such applications in these installation instructions, which is
supported by a professional maintenance program; installation of equipment in such environments is not recommended.

6. Dimming products – Dimming circuits and product compatibility must be validated by the installer before installation; SAL cannot be responsible for third party
changes in dimmer compatibility. 

7.  Suspended products – For installation safety, any suspended products must NOT be installed in high air movement spaces or locations subject to impact.

8. Light source replacements – (Non-replaceable light sources) - The light source of the product is deemed not replaceable, when the product reaches its end of life
the complete product, it must be replaced by a qualified installer. (Non-user replaceable light sources) - The light source of the product must only be replaced by the
manufacturer or qualified installer. Caution, risk of electric shock.

9. Interior downlights and sensors with remote drivers and electrical accessories  The mounting facilities provided for the transformer/driver (if any), need only be 
utilized if in the application of the product is required by AS3000. Drivers are not designed for installation environments that restrict conventional airflow.

10. Floodlight products – Unless nominated aiming restrictions or installation parameters apply, products are designed for installation environments between ground and 
15 metres in height, subject to the desired optical performance being achieved. For floodlight installation environments that have restricted access (eg: columns and 
roof-lines) which are subject to unstable electrical supply or electrical surges (which void warranty), consideration of the installation of an independent surge protector 
is strongly recommended.

11. Emergency enabled products – In the interest of transport and safety, emergency products are supplied with the battery disconnected. In addition to specific 
emergency commissioning instructions, this battery MUST be connected at the time of installation. Continual use in emergency mode greater than 240 hours without
recharge, will result in battery failure and void battery warranty.

Nominal frequency (Hz)

Product installation orientation

Operating ambient min/max (°C)

Product application

Operating humidity

Pixie connectivity

Storage ambient limit (°C)

IP rating*

Storage humidity

Attachment type

Enclosed in approved product

50

IP rating for interior products: The designated IP rating is “from below the ceiling” unless otherwise specified.
IP rating ALL products: Termination of the product must be made in accordance with the IP rating.

0 to 40

Interior residential or commercial

10% to 85% RH, NC
0 to 40

20
N/A

10% to 85% RH, NC

No

Model No.

Input (V)/(Hz) 

 

Dimension L x W x H (mm)

Sensor type

Microwave

SMS830

220-240/50

LED 300 / INCAND 1000W

White

122 x 31 x 29

Max loads

Colour

Reviews: