background image

Page 1 

F

F

@

@

S

S

T

T

3

3

2

2

8

8

4

4

 

 

1. Introduction 

This F@ST 3284u Cable Gateway is an Embedded Media Terminal Adapter (EMTA) which is CableLabs DOCSIS 3.0 and 

PacketCable 1.5 compliant. It provides high-speed Internet access as well as cost-effective, toll-quality telephone voice and 

fax/modem services over residential, commercial, and education subscribers on public and private networks via an existing 

CATV infrastructure. F@ST 3284u offers high-speed LAN connectivity with 4 Gigabit Ethernet ports and one integrated 

Wireless LAN access point compatible with IEEE 802.11a/b/g/n. The Wireless access point is operating on 2.4GHz band.   

Package Contents 

F@S T3284u Gateway                                              x1 

Ethernet Cable (RJ45) 

x1 

Phone Cable (RJ11)   

x1 

Quick Start Guide 

x1 

Power Supply Unit 

x1 

2. Hardware Connection 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

11 

10 

12  13  14 15 

1  2  3  4  5  6  7 

16 

LED Power ON/OFF 

16 

10 

11 

12 

13 

15 

14 

LED Downstream - indicate receiving RF DS traffic 

LED Upstream - indicate receiving RF US traffic 

LED Internet ON/OFF 

LED WiFi ON/OFF 

LED Telephone Line 1 

LED Telephone Line 2 

WPS button with Blue LED.   

Wireless ON/OFF button 

RJ-11 Telephone port lines 1 and 2 

Ethernet 10/100/1000 BaseT RJ-45 connector

 

Restore To Factory Defaults button 

RF coaxial F-connector 

Power plug 

Power switch ON/OFF 

USB port 

u

User Manual

Summary of Contents for F@ST 3284u












Reviews: