A
B
C
A
B
E
F
G
C
D
B
C
E
A
F
D
2
SCREW HOLES
FOR CATCH
1B
PEEL OFF
3
SCREW HOLES
FOR LOCK
1A
PEEL OFF
FOLD
HS025
ProGr
ade
HS132
Cor
e
2
SCREW HOLES
FOR CATCH
FOLD
2
SCREW HOLES
FOR CATCH
1B
PEEL OFF
3
SCREW HOLES
FOR LOCK
1A
PEEL OFF
FOLD
For adhesiv
e moun
t:
mar
k line
for ca
tch
piec
e as sho
wn
with r
ed line
mar
k line
for lock
piec
e as sho
wn
with r
ed line
adher
e lock as sho
wn
3
SCREW HOLES
FOR LOCK
1A
PEEL OFF
Green = Locked
Red = Unlocked
1
Catch
Lock
Lock/Unlock button
SecureTech
TM
lock indicator
Magnetic key
Screws (4 per lock)
Installation template (1 per lock)
©2011 Dorel Juvenile Group. All Rights Reserved. Tous droits réservés.
www.djgusa.com (800) 544-1108 www.safety1st.ca
Made in CHINA. Fabriqué en CHINE. Styles and colors may vary. Les styles et les couleurs peuvent varier.
Distributed by (distribué par) Dorel Juvenile Group, Inc., 2525 State St., Columbus, IN 47201-7494
Dorel Distribution Canada, 873 Hodge, St. Laurent, QC H4N 2B1 05/16/11 4358-5684
Complete Magnetic Locking System
HS130 User Guide
Parts & Features
CAUTION:
• This product is not a toy. Do not allow children to play with it. When not in use, keep out of reach of children.
• This product is only a deterrent. It is not a substitute for proper adult supervision. Discontinue use when child becomes old enough to defeat it.
WARNING:
• ADULT ASSEMBLY REQUIRED. KEEP SMALL PARTS AWAY FROM CHILDREN DURING ASSEMBLY.
• Keep magnetic key out of reach of children.
• This product contains magnets. Swallowed magnets can stick together across intestines, causing serious infections
and death. Seek immediate medical attention if magnets are swallowed.
• For indoor use only.
• Toxic and dangerous substances, as well as sharp edged or pointed objects, should always be placed “high up” or
totally inaccessible to small children.
BEFORE YOU BEGIN:
• Read all instructions before installing.
• Keep these instructions for future use.
• Remove all contents from packaging and discard box, and/or poly
bags.
• Do not return this product to the place of purchase. If any parts
are missing, email [email protected], call Consumer Relations
at (800) 544-1108, or fax at (800) 207-8182. You can also visit our
website at www.safety1st.ca. Have the model number ready (HS130)
and date code (manufacture date) located on product.
• Tools needed: Hand drill or power drill, 7/64” drill bit, Phillips head
screwdriver & pencil (not provided).
• Door/drawer geometry may prohibit use.
• Avoid close proximity to metal hardware or metal objects stored in
cabinets when planning product placement, as they might make it
difficult to operate the magnetic key properly.
• Avoid letting children see how you operate child safety devices.
Watching you disengage a lock or latch could enable them to learn
sooner how to defeat it.
• Remove adhesive bumper pads on your cabinet doors only if they
interfere with installation or operation of these locks.
1b
Determine Lock Placement
Cabinet Door and Drawer Types
There are many sizes, shapes and kinds of cabinet doors and drawer
fronts. To determine if our lock will work on your door/drawer follow
steps 1-8 below.
NOTE:
•
Doors with
inset panels (Image A)
may not have wide enough flat
surface
.
•
Drawers with
outer face panels
(Image B)
may not have enough room
to install this lock.
•
When locks don’t fit at the
top
of the cabinet, they may fit at the
side
(Image C)
.
Drawer with outer face panel
Inset frame
Top or side
1
Open door/drawer and choose a
possible location to install the lock.
Mark how far down the side of the
door/drawer or how far over on the
top of the door/drawer the lock will
be located
(Figures 1a and 1b)
.
2
Close cabinet door/drawer and
mark your lock position on the
cabinet base
(Figures 2a and 2b)
.
3
Peel paper (labeled
1A
) off
template
(Figure 3).
1a
Panel frame
2b
2
SCREW HOLES
FOR CATCH
1B
PEEL OFF
3
SCREW HOLES
FOR LOCK
FOLD
2
SCREW HOLES
FOR CATCH
1B
PEEL OFF
FOLD
1A
PEEL OFF
1B
PEEL
OFF
2
SCREW HOLE
S
FOR CA
TC
H
FOLD
2a
3
Inside
panel
G
