background image

1

B1-GRQ-2-OpGuide-v1-050125.pmd

GRQ3121 (1U, single channel, one input, two outputs)

GRQ3122  (2U, dual channel, one input & output per channel)

GRQ3121-S (1U, blank front panel slave, single channel, one input, two outputs)

GRQ3122-S (1U, blank front panel slave, dual channel, one input & output per channel)

GRQ2 Remote for Windows

TM

  Software included with every unit; runs up to 8 Graphi-Q2s per COM port

(maximum of 2 COM ports)

All front panel controls are analog-style; signal path is digital

“Tweek-n-Peek” feature:  Front panel adjustments of all parameters are shown in LED display screen

24-bit A/D and D/A conversion, 32-bit processing

20 to 20 KHz Frequency Response

+18 dBV Maximum Signal Input & Output

Floating Point SHARC Processor

>110 dB dynamic range

Each channel provides (now with fully independent processing on 1x2 units):

31-band graphic EQ, with ± 6 or 12 dB range  (selectable)

Crossover:  Bessel, Butterworth, and Linkwitz Reily filters; slopes to 48 dB/octave (Software only)

High Cut Filter (3KHz to 20KHz) and Low Cut Filter (20 Hz to 1KHz)

FBX Feedback Exterminator: up to 12 Filters, with Setup Mode (Auto Setup Mode via remote control)

Parametric Filters:  up to 12 filters, numeric or graphic control (Software only)

Compressor/Limiter, with controls for ratio, threshold, and gain (attack, release, and knee adjustable
with remote)

Digital Delay, with up to 1 second delay, adjustable in 20 microsecond increments

Bypass:  dedicated switches for FBX, EQ, and Delay with built in LED indicators

LED Segmented Indicators: FBX Filters, Level, Gain Reduction

LED Point Indicators: FBX Setup, Remote, EQ Range

LED Character Display: Delay setting, EQ fader boost/cut, High Cut Filter setting  Low Cut Filter setting,
Compressor Ratio, Threshold, Gain, and Staus Messages.

Back Panel:

XLR & 1/4" TRS inputs & outputs

RS-232 Serial input & output (additional serial input on the slave front panels)

Remote switching (8-position contact closure switch; allows switch selection of all 20 stored Graphi-
Q2 presets)

Graphi-Q2 Remote Software Features:

All front panel controls, plus more, including:

FBX filter depth & width adjustments; switchable to parametric filters (depth, width & frequency
adjustments)

Graphic EQ filter width adjustments

Password protection

View & edit frequency response curves

20 user-defined stored presets

Control and link up to 8 Graphi-Q2s (16 channels of audio) per COM port (1 or 2 ports can be used)

Future-proof FREE Flash RAM upgrade capability:  upgrade your firmware and software from the Sabine
website (www.Sabine.com)!

Summary of Features

S

UMMARY

 

OF

 F

EATURES

Operating Guide Version 1: for Sabine Graphi-Q2s with:

GRQ2 Firmware Version 2.20

GRQ2 Remote Software Version 5.0

Summary of Contents for GRAPHI-Q2

























































Reviews: