For example, we connect the RunCam Split Mini to the UART 3 interface on the Flight
Controller: connect the Flight Controller to the computer, then open the configurator
software of the Flight Controller. (Open up the configurator that matches the firmware
you are running, Betaflight Configurator for Betaflight, Cleanflight Configurator for
Cleanflight). In the Peripherals column of the line UART3 (on the Ports tab), select
RunCam Device and click Save And Reboot.
In the Flight Controller Configurator, navigate to the Modes tab. There are new
CAMERA WI-FI, CAMERA POWER and CAMERA CHANGE modes
Assign any available channel to the function you need, for example:
·
CAMERA WI-FI: in the OSD of the camera, this is used to confirm your selection.
·
CAMERA POWER: start/stop the video. When in the OSD of the camera, this is used to
move to the next menu item.
·
CAMERA CHANGE MODE: switch among the two modes: video and OSD
setting mode. When in the OSD of the camera, this will exit the menu
·
Assign the AUX1 to the CAMERA WI-FI, range 1900-2100
·
Assign the AUX2 to the CAMERA POWER, range 1900-2100
·
Assign the AUX3 to the CAMERA CHANGE MODE, range 1900-2100
Please choose your Model on the controller, then access to the MIXER interface and
assign the channel to the switch of the controller. Take opentx 2.2.0 for example, assign
the channels CH5, CH6 and CH7 to SA, SB and SD respectively
Power the Flight Controller and the RunCam Split Mini
·
Set the SA to the bottom, the camera starts/stops the video
·
Set the SD to the bottom, the camera switches among the two modes:
video and OSD setting mode
www.runcam.com
Powering On/Off
Simultaneously press the Power/Shutter button and
Mode Switch button.
Camera Status Light:
Orange is On
• Press the Power/Shutter button to move to a setting.
• Press the Mode Switch button to select.
• Long press the Mode Switch button to exit the menu.
Camera Status Light:
Blue blinks
Press the Power/Shutter button to start/stop recording.
In Standby Mode, long press the Mode Switch button to
cycle through the three modes: Video/Photos/OSD settings.
Long press the Power/Shutter button
Standby Mode
Camera Status Light:
Blue is On
Firmware
Upgrading
Camera Status Light:
Orange blinks
https://goo.gl/5Mq8zw
Mode Switching
Video Mode
OSD Setup Mode
Forced Shutdown
In standby mode, press the Mode Switch button three times
in rapid succession (within 2 seconds). When resetting is
complete, the status light (orange) blinks twice, and the
camera automatically shuts down.
Reset
FOV
Video Resolution
Video Files
Image Resolution
TV Output
Interface
Max Micro SD Card Supported
Dimensions
Power Input
Working Current
Weight
FPV FOV 130°/Recording FOV 165°
1080@60fps/1080@30fps/720@60fps
MOV
2 MP
NTSC (720*480)/PAL (720*576) Switchable
Micro USB / UART
64G(need Class 6 or above,
recommend Class 10/UHS-I/UHS-II)
PCB 27*29mm / Lens Module 19*19mm
Hole Distance of Installation
20*20mm
DC 5-15V / DC 5V(USB)
650mA @5V/270mA @12V
15g
Please visit:
https://support.runcam.com
TX
RX
MicroSD Card
VCC +(5-15V)
GND
Video
Micro-USB
Capacity up to 64GB; Please use high speed cards(Class10/UHS-I/UHS-II)
Please push the metal piece a little bit up with one hand like showed in above step 1
and then press the SD card(step 2) with another hand to let the card pop out.
1
2
Mode Switch Button
Power/Shutter Button
Sensor Connector
Metal Cover
RunCam
2
1
PDB
GND
Video
Power in
GND
5-15V
5-15V
Power in
GND
GND
Video
5V
GND
PDB
UART Interface
FC
GND
GND
RX
RX
TX
TX
User Manual
·
·
Instruction Diagram
·
Installation Diagram
·
Lens Module Connection Diagram
·
Micro SD Card
·
Basic Camera Operation
·
Transmitter Connection Diagram
·
Flight Controller Set
·
Technical Support
·
Parameter
Side A
Side B
Microphone
USB
DC 5V
Warning:
USB port only supports DC 5V
Warning:
Please press the Metal Cover(showed above) to make sure the Sensor
Connector fixed steadily.
Method One (Recommended):
connect by the soldering pads
Video Transmitter
Video Transmitter
Method Two:
connect by the TV-out and power USB cable
Warning:
USB port only supports DC 5V
Preparation
·
Firmware: CleanFlight (≥2.1.0) / BetaFlight (≥3.2.0)
·
Any available UART interface on the Flight Controller
1. Connect the RunCam Split Mini with the UART interface of the Flight Controller
2. Make the Flight Controller recognize the RunCam Split Mini
3. Instructions of the functions of the camera and assigning transmitter channels
to them
4. Assign the channel to the switch of the controller
5. Test
