T310n Access Point
Quick Setup Guide
NOTE: The minimum software revision for the T310n is
ZoneDirector (ZD) 10.1 or later, or SmartZone (SZ) 3.6 or
later, or standalone AP firmware 108.0 or later.
This Quick Setup Guide provides step-by-step instructions on
how to field-install the Ruckus Wireless T310n access point
(AP). For detailed information on planning the installation,
performing a site survey, and operating the T310n, refer to the
Ruckus Wireless Outdoor Access Point User Guide
, available
at https://support.ruckuswireless.com.
WARNING!
Only trained and qualified personnel should be
allowed to install, replace, or service this equipment.
WARNING!
Installation of this equipment must comply with
local and national electrical codes.
CAUTION!
Make sure that you form a 80mm - 130mm
(3”-5”) drip loop in any cable that is attached to the AP or
the building. This will prevent water from running along the
cable and entering the AP or the building where the cable
terminates.
CAUTION!
Be sure that grounding is available and that it
meets local and national electrical codes. For additional
lightning protection, use lightning rods and lightning
arrestors.
CAUTION!
Make sure that proper lightning surge protection
precautions are taken according to local electrical code.
WARNING!
Ruckus Wireless strongly recommends that you
wear eye protection before mounting the T310n.
This Guide in Other Languages
• 请
从
以下
网
站
请
得
请
指南的
请
体中文版
.
• Vous trouverez la version française de ce guide à l'adresse
suivante
https://support.ruckuswireless.com
•
このガイドの日本語版は
でご
覧
ください。
•
이
가이드의
한국어
버전은
웹
사이트
(
)
에서
확인하시기
바랍니다
.
• Veja a versão em português (Brasil) deste guia em
• Puede ver la versión en español (América Latina) de esta
https://support.ruckuswireless.com.
Before You Begin
Before deploying Ruckus Wireless products, please check for
the latest software and the release documentation.
• Release Notes and other user documentation are available
at
http://support.ruckuswireless.com/documents
• Software upgrades are available at
support.ruckuswireless.com/software
.
• Open source information is available at
• Software license and limited warranty information are
http://support.ruckuswireless.com/warranty
Before deploying your Ruckus Wireless Access Point, verify
that all items listed in
Package Contents
are included in the
package. If any item is damaged or missing, notify your
authorized Ruckus Wireless sales representative. Also,
make sure that you have the required hardware and tools.
Required Hardware and Tools
• No. 2 Phillips screwdriver
• Small flat-blade screwdriver
• Torque wrench or torque screwdriver with sockets
• Long-nose pliers
• Electrical wire stripping and terminal crimping pliers
• Pipe or pole --OR-- a sturdy flat surface
• Electric drill with drill bits and customer-supplied wall
anchors, flat washers, and hex nuts for flat-surface mount
Package Contents
A complete T310n field installation package includes all of the
items listed below (see Figure below for illustrations):
• T310n Access Point (A)
• M25 data cable gland (B)
• Ground wire with lug (C)
• Pole/Wall Mount Bracket Kit (D)
• Four steel pipe clamps
• Service Level Agreement/Limited Warranty Statement
• Declaration of Conformity
• Regulatory Statement
• Ruckus Wireless AP Getting Started Guide
• This Quick Setup Guide
FIGURE 1 T310n Package Contents
T310n Sector Antenna Coverage
The T310n 30-Degree Narrow Sector AP is best deployed
where internal-antenna narrow beamwidths can provide
exceptional coverage to a narrow sector, or can support
extended reach in a point-to-point deployment. See the
following illustrations for typical internal-antenna coverage
patterns and high-density narrow-sector coverage pattern.
FIGURE 2 Typical AP narrow sector or point-to-point coverage
Copyright
®
2017 Ruckus Wireless, Inc.
Page 1 of 4
Published September 2017, Part Number 800-71623-001 Rev A
