![background image](http://html.mh-extra.com/html/ruckus-wireless/902-0178-0002/902-0178-0002_mounting-manual_1498890001.webp)
Copyright © 2013 Ruckus Wireless, Inc.
Published July 2013, Part Number 800-70544-001 Rev A
Page 1 of 2
ZoneDirector
™
5000 and
SmartCell Gateway
™
200
Rack Mount Kit Mounting Guide
This
Rack Mount Kit Mounting Guide
provides step-by-step
instructions on how to install the Ruckus Wireless ZoneDirector
5000 (ZD) or SmartCell Gateway 200 (SCG) into a server rack
using the Ruckus Wireless 902-0178-0002 kit. Both ZoneDirector
5000 and SCG are standard 2U form factor servers designed for
mounting in a standard EIA 19” server rack.
B
EFORE
Y
OU
B
EGIN
Before deploying your Ruckus Wireless product, verify that all
items listed in “Package Contents” below are included in the
package. If any item is damaged or missing, notify your
authorized Ruckus Wireless sales representative. Also, make
sure that you have prepared the required hardware and tools.
NOTE:
Some standard EIA 19” server racks have square or
slotted mounting holes. The fasteners in this kit may not work
with these racks, requiring the customer to supply rack-mount
fasteners.
WARNING:
Observe careful handling, kit may contain sharp
edges.
NOTE:
Using sliding rails could result in non-compliance with
Seismic Zone 4 requirements of NEBS-3 certification.
T
HIS
G
UIDE
IN
O
THER
L
ANGUAGES
请从以下网站获得该指南的简体中文版
https://support.ruckuswireless.com
.
Vous trouverez la version française de ce guide à l'adresse suivante
https://support.ruckuswireless.com
.
こ の ガ イ ド の日本語版は
https://support.ruckuswireless.com
で ご覧 く だ さ い。
이
가이드의
한국어
버전은
웹
사이트
(
https://support.ruckuswireless.com
)
에서
확인하시기
바랍니다
.
Veja a versão em português (Brasil) deste guia em
https://support.ruckuswireless.com.
Puede ver la versión en español (América Latina) de esta guía en
https://support.ruckuswireless.com.
R
EQUIRED
H
ARDWARE
AND
T
OOLS
•
Medium flat-blade screwdriver
•
No. 1 Phillips screwdriver
•
11/32” nut driver
•
Ruler for measuring rack depth
•
12 customer-supplied server rack fasteners (only required if
not using the factory-supplied rack mounting screws and
rack bar nuts, E and F in Figure 1)
P
ACKAGE
C
ONTENTS
A complete rack mount installation kit includes two rail
assemblies and all of the items listed below:
•
Two outer rails with short front brackets (A in Figure 1);
shipped attached to B in Figure 1
•
Two inner rails with safety stops (B in Figure 1); shipped
attached to A in Figure 1
•
Four long brackets (C in Figure 1)
•
Two front locking brackets (D in Figure 1)
•
Twelve #10-32 x 3/4” (19mm long) rack mounting screws
with nylon washers (E in Figure 1)
•
Four server rack bar nuts (F in Figure 1)
•
Eight #8-32 x 1/2” (12.7mm long) pan head screws with hex
nuts and flat and lock washers (G in Figure 1)
•
Eight #8-32 x 1/4” (6.35mm long) pan head screws (H in
Figure 1)
•
This
Rack Mount Installation Guide
Figure 1: Rail assemblies and hardware
NOTE:
This kit may include extra screws, nuts and washers. You
may use the extras wherever required.
S
TEP
1: S
EPARATE
THE
R
AIL
A
SSEMBLIES
INTO
O
UTER
AND
I
NNER
R
AILS
These are shown as A in Figure 1 and B in Figure 1, respectively.
1
Extend the inner rail (1 in Figure 2) until it locks.
2
Press down the spring safety lock (2 in Figure 2) to release
the inner rail.
3
Remove the inner rail from the outer rail assembly (3 in
Figure 2).
Figure 2: Separating the rail assemblies
S
TEP
2: A
SSEMBLE
THE
R
EAR
B
RACKETS
ONTO
THE
O
UTER
R
AILS
1
Measure the depth of your server rack. Use this
measurement to adjust the length of the outer rail and
bracket assemblies.
NOTE:
Leave the outer rail assemblies loose for now. You will
tighten them after the outer rail assemblies are positioned in
the rack.
2
If your rack depth is between 23.25 and 34 inches (59.6 and
86.4cm), use four #8-32 x 1/2” pan head screw sets (G in
Figure 1) and loosely attach two long brackets (C in Figure 1)
to the two outer rails (A in Figure 1) as shown in Figure 3.
If your rack depth is between 29.5 and 34 inches (74.9 and
86.4cm), also adjust the short front brackets (part of A in Fig-
ure 1) by loosening the #8-32 x 1/2” pan head screw sets (G
in Figure 1), adjusting the front bracket positions as
required, and retightening these screw sets.
3
If your rack depth is more than 34 inches (86.4cm), use four
#8-32 x 1/2” pan head screw sets (G in Figure 1)and loosely
attach two long brackets (C in Figure 1) to the two outer rails
(A in Figure 1) as shown in Figure 3.
Then remove the short front brackets (part of A in Figure 1),
and replace them with long brackets (C in Figure 1).
F
G
H
E
A
C
B
D
(Front
of
Rack)
(Rear
of
Rack)
(shipped attached
to each other)