Beat
Mirror
Installation & aftercare instructions
Please retain for future reference
2
2
2
OUTSIDE
ZONES
2
ZONE
1
0.75m
2.25m
3.0m
0.6m
0.6m
0.75m
Bathroom Zones Diagram
Distances from a bath tub or shower tray
TB.RR.MLE420 | 09.15 V3 .00
Roper Rhodes, Brassmill Lane Trading Estate, Bath, BA1 3JF
TEL: 01225 303 900 | FAX: 01225 448 877
www.roperrhodes.co.uk
Product code
MLE420
ELECTRICAL SAFETY INSTRUCTIONS
(Applicable to UK Installations only)
All fittings must be installed by a competent person, in
accordance with current IEE wiring regulations. If in doubt
consult a qualified electrician
IMPORTANT
Always switch off the electrical supply at the mains during
installation and maintenance. It is recommended that the
fuse is withdrawn or the circuit breaker is switched off for the
necessary circuit before installation commences.
Fitting in Bathrooms is subject to the appropriate zone in
accordance with IEE Regulations. This product is suitable for
zone 2 and outside zones. IT IS NOT suitable for installation in
Zone 0 or Zone 1. It is also not suitable for installation in
saunas, steam rooms or shower cubicles. This product is only
suitable for permanent installation. DO NOT connect to a
trailing plug and socket outlet. Although this product has an
Ingress Protection rating of IP44 it is only suitable for indoor
use. Do not attach the product to surfaces that are damp or
otherwise electrically conductive.
INSTALLATION CARE & SAFETY
Wear suitable eye protection when drilling. Take care when
using power tools near water - the use of a residual current
device (RCD) is advised. Beware of hidden cables or pipes.
Take care if drilling on tiled surfaces in case the drill slips. A
piece of masking tape applied to the wall before marking out
the fixing holes will stop the drill from wandering.
IMPORTANT
DO NOT strike glass components with
hard or pointed items. DO NOT place
very hot or very cold items against or in
close proximity to glass surfaces unless
an adequately thick insulation material
is used to prevent such items coming in
contact with the glass.
The nominal thickness of the mirror
glass used in this product is 5mm and is
film backed for safety. If the glass
becomes chipped or broken replace
immediately.
This product should be positioned well
away from curtains and other fabrics.
Never cover the mirror. This product is
heated, we recommend that it is turned
off after use and should never be left on
for prolonged periods of time
This product could be dangerous and is
only to be installed by a competent
person.
“There is no sound from my Beat Mirror.”
- The volume on either device is muted or turned down.
- There is a problem with the
Bluetooth
®
connection - try erasing the connection on the audio device
and then re-pairing.
- There may be interference from other nearby
Bluetooth
®
enabled devices - try turning them off.
- The connected devices are too far apart and out of range - try moving the devices closer together.
“I cannot pair the mirror with my
Bluetooth
®
device.”
- The mirror may not be in pairing mode - to do this press the button.
There will be a short lag
with no visible activity while the device powers on.
The indicator light will flash and the mirror will beep
to confirm pairing mode.
- The
Bluetooth
®
capability of your chosen device is turned off or out of range.
- There was a problem during pairing - some devices will pair automatically when selected some will
require a pass code or acceptance of the connection before they will finalise the pairing.
- Refer to your
Bluetooth
®
device’s instruction manual to ensure it supports the A2DP (stereo
Bluetooth
®
)
profile.
- If attempting to connect to a PC or Mac computer, ensure that your Beat Mirror is set as the audio
output device within the audio settings menu of the device. You may need to play a track to finalise the
connection.
“The sound quality is poor.”
- Your
Bluetooth
®
device may be close to being out of range and should be moved closer to the mirror.
- For those devices that support the use of Applications, there may be too many running in the
background which can affect the amount of internal resources available on the device to transmit
audio. Closing any non-essential applications may improve audio quality.
- Similarly, if the selected device has Wi-Fi capabilities, turning this off may improve audio quality.
- There could have been a problem during the initial pairing of devices. Erase the connection using your
Bluetooth
®
device and re-pair.
- For those devices with in-built sound equalisation, adjusting these settings can greatly improve the
sound quality of any audio played through your Beat Mirror.
“My Beat
mirror is not automatically reconnecting with my
Bluetooth
®
device.”
- The mirror will automatically reconnect with paired devices when both devices
Bluetooth
®
capabilities
are turned on. Depending on the manufacturer of the
Bluetooth
®
device, the order in which the devices
are turned on to automatically connect may vary. In some cases it will be necessary to turn on
Bluetooth
®
capabilities on the audio device before turning on the mirror.
The
Bluetooth
®
word mark and are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by
Roper Rhodes is under license. Other trademarks and trade names are those of their respective owners.
with
Bluetooth
®
wireless technology
Troubleshooting
C
M
Y
CM
MY
CY
CMY
K
MLE420 _ RR_Beat Illuminated Mirror Instructions v4.pdf 1 03/09/2015 09:12:21
