RT5 Thermostat Instructions
Before fitting this thermostat, (stat) make sure to read these instructions fully. The installer must be competent and qualified to work with electrics before making any
connections to mains power. It is the responsibility of the installer to make sure the thermostat is installed in a suitable location, programmed correctly and also suitable
for use with your chosen heating system. Failure to understand and follow these instructions correctly can cause damage to the thermostat, heating system and create a
hazardous environment to health. Make sure to check all ratings given in these instructions and also ratings of the heating system this thermostat will be controlling to be
sure they are all compatible.
1: Touch screen for easy clean IP rated control.
2: 0.5 degrees accuracy
3: Child lock
4: Battery backup for program settings
5: Holiday and Hold Modes
6: Internal and external temperature sensors.
7: Clear back lit flat screen
8: Low profile design
1: 100-240Vac - 50/60HZ
2: Max load 16A@250V/AC
3: Electromagnet Switch Relay
4: Max temperature range 0-75°C
5: Default temperature setting range 5-35°C
6: External NTC 10k Probe
Features
Specifications
Screen Icons & Keys - How to use set and make changes were possible.
Read this section on automated program settings fully before trying to program the thermostat.
NOTE: The thermostat does not turn on or off it simply changes the set / desired temperature 6 times per day on a 7 day cycle.
NOTE: When programming the thermostat you must work in a linear time line from zone 1 - 6 and not jump back and forward in time.
NOTE: If you do not want the heating to come on in any part of the day / zone simply set a low temperature for that zone and the thermostat will not turn the heating on
unless the temperature drops below the set temperature.
NOTE: For ease of programming you can select a 5+2 (factory default),6+1 or 7 day cycle setting. For more information on this or how to change see advanced options A6.
NOTE: When programing the thermostat if the screen is left untouched for 10 seconds the thermostat will save changes made and revert back to the home screen. This
time can be increased in advanced options A - A5 up to 30 seconds before the thermostat saves and reverts back to home screen if more time is needed.
START:
To program each zone hold down SET for 5 seconds and the time will flash and zone 1 will appear in top right corner. The times and temperatures you put into
the next 6 zones will be copied across to all days showing across the top right of the screen. Follow the next 3 steps below to work through and set all 6 zones for these
days without delay, (it can be helpful to have your time and temperatures for all zones written down first).
NOTE: If you have selected 0 (=5+2) in advanced setting A - A6 you will have days 12345 showing across top right of screen at this stage, if you selected option 1 (=6+1)
you will have days 123456 showing or if you selected optio 2 (=7) you will have days 1234567 showing. The times and temperatures you put into the next 6 zones will be
copied across to all days showing on your screen. In step 5 below you will compete the missing days 6,7 or 7 if you selected options 0 or 1 in advanced options A - A6
1:
Change the hours using UP/DOWN buttons for when you want to wake up (zone 1 time) and tap SET to move to minutes.
2:
Minutes will flash next, change these again for when you want to wake (zone 1 time) and once correct tap SET to move to temprature.
3:
Set temperature will now flash. Change the temperature to the desired temperature and tap SET again to move / set up next zone..
4:
You will now see Zone 2 appear in the top right and the hours will be flashing again. Repeat steps 1 – 3 above for all 6 zones.
# If you selected option 0 (=5+2) or 1 (=6+1) in advanced option A - A6 go to instruction step 5 below.
# If you selected option 2 (=7) in advanced options A - A6 you are finished.
5:
Once you complete zone 6 and tap SET you will now see zone 1 reappear top right but the days will change to weekend days. Days 6+7 or only 7 will now be showing.
You now need to repeat steps 1-3 above for all 6 zones. These are your weekend zone settings. These days are typically programmed differently to the weekday
NOTE: Thermostat must be ON and screen LIT UP to operate this thermostat unless stated otherwise.
ON / OFF
Turn ON/OFF: Quick tap POWER button to turn on and turn off.
To change the time and day tap the OK button. Minutes will flash, use the UP / DOWN buttons to set the minutes. Once correct tap OK again and the
hours will flash. Again make changes using UP / DOWN buttons and then tap OK again. Now day will flash, (note the 7 days of the week are represented
as numbers 1-7 with 1 being Monday) again make changes using UP and DOWN buttons and then tap OK to finish.
Manual mode activated. Thermostat will hold the current set temperature unit a change is made. To select Manual mode simple tap the SET button to
swap between Manual and Auto modes.
Automated / Programmed heating cycle activated. Stat will continuously run the pre-set automated 7 day heating cycle. To select this simply tap the SET
button to swap between Auto and Manual modes. See ‘Automated Program Settings’ for how to set up and program the automated heating cycle.
Automated program - Temporary override. If you wish to manually change the temperature when running the stat in Auto mode simply use the
UP/DOWN buttons to change the temperature. The new temperature will now be set and held until the next automated program cycle zone kicks in.
During this temporary override time you will see in the bottom left of the screen. Once this time zone ends and the programed cycle moved into
the next time zone the thermostat will revert back to the preprogrammed temperature and time cycle. This symbol will then be replaced with
Holiday mode is used to set a single temperature for a set number for days such as when away on holiday. To set up press and hold OK for 5 seconds to
enter holiday mode setting. OFF or ON will now be flashing. Use UP / DOWN buttons to select ON and then tap OK. Number of days will then be flashing.
Use UP/DOWN buttons to select desired number of days and tap OK again. Temperature will be flashing. Select the desired temperature using
UP/DOWN buttons and tap OK to complete set up. Screen will now revert back to home screen and suitcase will now be showing. To check how many
days and or time is left before holiday mode ends tap the UP / DOWN button once. NOTE: if you tap the SET button during the holiday mode period,
holiday mode will be cancelled and the thermostat will revert back to manual mode.
Child lock to stop unwanted tampering or temperature changes. To activate or turn off simply hold the DOWN button for 5 seconds until the padlock
appears / disappears.
When the flame is showing, power is going to heating. The flame will show until the set temperature is achieved. If the set temperature is below the
actual temperature the flame will not show as there is no need for the heating to be on.
External NTC sensor / Floor sensor, (not air sensor) is being used to measure main temperature on screen. NOTE: Air or floor or both sensors can be
selected (see advanced options B for setting options). WHEN USING UNDERFLOOR HEATING IT IS IMPORTANT TO USE FLOOR SENSOR ONLY.
Time / Day
Feature
Wiring
SET
OK
Days of week
Auto Porgram Zones 1- 6
Time
Power On/Off
SET Button
OK Button
Up/Donw Buttons
Child Lock
Actual Temprature
Set Temprature
Floor Sensor
Manual Mode
Holiday Mode
Heating On
Automatic Mode
Floor S
ensor
V0122
