1
2
Drum stand
Assembly procedure
Drum sound module / Pads / Others
3
4
5
For a left-handed setup
Connection procedure
Setup Guide
Before using this unit, carefully read “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (the leaflet “USING THE UNIT SAFELY,” “TD-07 Owner’s Manual,” and the TD-07KVX
Setup Guide). After reading, keep the document(s) where it will be available for immediate reference.
Check the included items
Assemble the drum stand
* When checking the items
included with the drum
stand, refer to “MDS-
Compact Owner’s Manual.”
* The tip of the mount is sharp. Handle it with care.
* When setting up or storing the stand, be careful not to pinch the fingers you use to
handle the stand.
Attach the parts
Connect the pads to the drum sound module (TD-07)
Connect the AC adaptor
and speakers
Connect the AC adaptor, headphones, or speakers as described in the “TD-07
Owner’s Manual.”
* To prevent malfunction and equipment failure, always turn down the volume, and turn
off all the units before making any connections.
The setup described in this guide is for right-handed players. To set up for a left-handed player,
reattach the components as follows.
5
Exchange curved pipes (L) and (R), and straight pipes (L) and (R), left-for-right.
5
Attach holder (C) and the snare pipe to the right side.
5
Exchange the pads and cymbals with their attachment mounts left-for-right.
5
Exchange the drum sound module with its sound module mount left-for-right.
9
When you’ve finished making connections, turn on the power as described in the “TD-07 Owner’s Manual,” and
verify that you can hear sound.
This completes assembly and connections.
Connect the connection cables as shown in the illustration.
© 2021 Roland Corporation
* The drum stand assembly procedure is for right-handed players. If you want to set up
the stand for left-handed players, refer to “Assembly for left-handed players” below.
* Adjust the position and height of the pads and pedals according to your height and
tastes, so that they are easy to play.
* Insert the plug firmly,
making sure it’s all
the way in.
1.
Connect the connection cable to
the drum sound module as shown
in the illustration below.
Insert the connector all the way,
then turn the knobs to fasten it
securely.
2.
Labels are affixed to the connection
cable to indicate the pads to be
connected. Make connections as
shown in the illustration at right.
TD-07KVX
1.2 m
(48 inches)
* To prevent the drum stand from tipping over, do not
position the stand leg pipes at the two ends more
than 1.2 meters (48 inches) apart.
CY-12C
PDX-12
PDX-8
PDX-8
PDX-8
CY-13R
KD-10
VH-10
TD-07
Diameter: 6.0–7.0 mm
(0.236”–0.276”)
Diameter: 11.7 mm (1/2”)
Max.
Attach the hi-hat (VH-10)
Motion Sensor Unit
CONTROL OUT jack on the
farther side
Clutch screw
Hi-Hat
“Roland” logo on the
farther side
Insulating Plate
Sponge side up
Compatible hi-hat stand
Attach the snare (PDX-12) and toms (PDX-8)
Attach the kick pedal
Install the kick pedal securely.
Use caution regarding the following to prevent the drum stand from
falling over.
5
Adjust the rod height so that no part of any cymbal is higher than
1.2 meters (48 inches) above the floor.
1.2 m
(48 inches)
OK
Not OK
5
Attach the cymbals in such a way that the center of the cymbal does
not extend beyond the rear pipes of the stand.
Adjusting the position of the cymbal
Cabling diagram for the connection cable
(As seen from the back)
CR1
T1
KIK
HH
SNR
CR2
TD-07
* Fasten the cables so that they will
not obstruct your playing; use cable
clips and cable ties.
Make sure to wrap the cable ties
around the pipes.
HHC
8
Kick pad (KD-10)
8
V-Hi-hat (VH-10)
8
V-Cymbal for crash
(CY-12C)
8
V-Pad for snare
(PDX-12)
8
V-Pad for tom
(PDX-8 x 3)
8
V-Cymbal for ride
(CY-13R)
8
Drum sound module
(TD-07)
8
Connection cable
8
AC adaptor
8
Setup Guide (this document)
8
Owner’s Manual set
As soon as you open the package, check to see that all items are included. If anything is missing, please contact your dealer.
* This package does not include a kick pedal, and a hi-hat stand. Use with a commercially available kick pedal and hi-hat stand.
CY-12C
PDX-12
PDX-8
PDX-8
CY-13R
KD-10
VH-10
TD-07
PDX-8
(T1)
(T2)
(T3)
(SNR)
(KIK)
(HH)
(CR1)
(RD) (CR2)
Remove the caps, remove holder (C) and the snare pipe,
and reattach them to the right side.
Assemble the stand as the “B” type (for ride cymbal), following the steps in the “MDS-Compact Owner’s Manual.”
Adjust the location at which
the KD-10 is installed so that
it’s at a comfortable position
for playing.
After exchanging the curved pipes, attach
the holders so that the marks on the pipes
are visible through the gaps of the holders.
Mark
Straight pipe
R (short)
Curved pipe R
(including the pad mount)
Straight pipe L (long)
Curved pipe L
Attach the crash cymbal (CY-12C) and ride cymbal (CY-13R)
“Roland” logo on the farther side
Cymbal nut
Felt washer
* Use the cymbal nut and felt washer that are
included with the drum stand.
1.
Position the cymbal so that the stopper (convex
portion) of the cymbal mount is aligned with the
concave portion of the bottom of the cymbal.
2.
Tighten the cymbal nut enough to allow an
appropriate amount of sway.
Stopper
(convex
portion)
8
Drum sound module
holder
Cymbal mounts
Pad mounts
Pad mounts
* Cymbal mount
If the stand wobbles, loosen
this hand knob and adjust
the height.
MEMO
The mount holder and cymbal mount marked with an asterisk are not used on the TD-07KVX. The mount
holder is used when mounting a drum sound module aside from the TD-07, and the cymbal mount is used
when adding/changing a drum sound module and adding a cymbal, so keep these parts for later use.
* Mount holder
Remove this, as it is not used on
the TD-07KVX.
T3
T2
CR1
T1
KIK
RD CR2
TD-07
HHC
SNR
HH
T2
T3
Cabling diagram for the
connection cable
(As seen from the back)
*
5
1
0
0
0
7
6
4
4
1
-
0
1
*
RD
Loosen
Tighten
Pad mount
Loosen
Tighten
Pad mount
Knob
Label
BOW/EDGE
OUTPUT jack
BELL
OUTPUT jack
RD plug
CR2 plug
TRIGGER OUT
Jack
CONTROL OUT
Jack
HH plug
HHC plug
Attach the drum sound
module (TD-07)
1.
Use the drum key to loosen the
bolt A of the drum sound module
holder, then attach the drum
sound module holder to straight
pipe “L” (long) and tighten the
bolt.
2.
Use the bolt B of the drum sound
module holder to attach it as
shown in the illustration.
Straight pipe
L (Long)
Bolt A
Drum sound module holder
Bolt B
Drum key
NOTE
When handling the hi-hat control pedal, kick pedal, or cymbal pads, take care not to pinch your fingers
between movable parts and the main unit. If using this in a location where children are present, be sure to
provide adult supervision or guidance.
