Roberts Gorden CoRayVac B-10 Instructions Manual Download

Page: 1 / 26

Fuel Conversion Kit Instructions

B-2
B-4
B-6
B-8
B-9
B-10

B-12
B-12a
E-9
E-12
E-12a

Models:

P/N 227102NA Original Issue 03/00

Roberts-Gordon

1250 William Street
P.O. Box 44
Buffalo, New York 14240-0044
Telephone: 716.852.4400
Fax: 716.852.0854
Toll Free: 800.828.7450
http://www.rg-inc.com

Roberts-Gordon Canada Inc.

241 South Service Road West
Grimsby, Ontario L3M 1Y7 Canada
Telephone: 905.945.5403
Fax: 905.945.0511

Custom-Engineered Gas-Fired Low-Intensity

Infrared Heating Systems

WARNING

Installation must be done by a contractor qualified

in the installation and service of gas-fired heating

equipment or your gas supplier.

Improper installation, adjustment, alteration, service

or maintenance can result in death, injury or property

damage. Read the installation, operation and service

manual thoroughly before installing or servicing

this equipment.

DO NOT store or use petrol or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

FOR YOUR SAFETY

If you smell gas:

1. Open windows.

2. DO NOT try to light any

appliance.

3. DO NOT use electrical

switches.

4. DO NOT use any telephone

in your building.

5. Leave the building.

6. Immediately call your local

gas supplier after leaving

the building. Follow the gas

suppliers instructions.

7. If you cannot reach your gas

supplier, call the Fire

Department.

Installer

Please take the time to read and understand

these instructions prior to any installation.

Installer must give a copy of this manual to the owner.

Owner

Keep this manual in a safe place to provide your

serviceman with information should it become

necessary.

Quality in Any Language™

Summary of Contents for CoRayVac B-10



























Search results

Summary of Contents for CoRayVac B-10

Reviews:

Related manuals for CoRayVac B-10

Brands by name

Popular brands

Roberts Gorden CoRayVac B-10, Instructions Manual

Search results

Summary of Contents for CoRayVac B-10

Reviews:

Related manuals for CoRayVac B-10

Brands by name

Popular brands