![background image](http://html1.mh-extra.com/html/richell/60025/60025_instruction-manual_1454468001.webp)
×
①
②
①
②
Manuel d’ instruction
Thank you for choosing Richell's Product. Please read this instruction manual carefully before using this product, and keep
for future reference. If you give this product to someone else, please also give this instruction manual to the new owner.
Please note some parts of the figures shown below may be slightly different from the actual product, for your better
understanding of the structure and proper use.
Instruction Manual
60025
For litter box training for kitten, bring them near the litter box every two or three hours after breakfast, so the training process
can be faster.
(1) Privacy, Please;
Place the litter
box where your cat can be
comfortable (a corner of the room
where it is dark). Once its placed,
please do not remove.
(2) Where is my box?;
When your
cat starts to sniff around and
becomes anxious, bring your cat near
the litter box.
(3) Job well done!;
After your cat
successfully uses the litter box,
praise them. The cat remembers
the litter box faster when praising
continuously for about a week.
(Please be patient.)
(4) Accidents happen;
When your cat
misses the litter box, wipe the area
with a paper towel to remove any odor
marks. (Put the soiled paper towel
inside the litter box to leave the odor
mark in, so your cat can track back
inside, not outside of the litter box.)
Important!
Caution
Opened Lid
Scoop
Scoop
Scoop Cover
Hood
Lock
Handle
Base
* If you insert the scoop upside down,
the scoop cover will not close tightly.
l
Make sure that the side locks of the hood are firmly fitted to the base.
l
Do not place this product in direct sunlight. It may cause a deformation and/or product damage.
l
Keep this product away from all heat sources at all times. Also, please do not pour in boiling water. It may cause a
deformation and/or product damage.
①
Hold under the hole on the base using one hand.
②
Then, use other hand to open the lock part on the hood by
lifting. Do the same step on the other side to remove the hood.
l
While removing the top shield, the remaining litter
may be in the product. Remove the top shield in an
area where litter can be spilled.
l
This product is designed for use as an indoor cat litter pan.
Do not use this product for anything other than its intended use.
l
Do not use this product as a toy for child.
l
Do not lift this product with your cat.
l
Do not lean on or place objects on this product to avoid unexpected injuries
and/or product damages.
l
When lifting this product, use both hands and lift from the base. If you lift from
the hood, it may cause product to drop and damage the product.
l
A leaking issue may happen when your cat urinates where the hood and base are attached together.
l
Do not handle it roughly, such as dropping it or hitting it. It may cause an injury or damage.
Dimension
UPC
Material
Base / Hood / Scoop Cover / Scoop : Polypropylene
15.0"W x 19.0"D x 16.0"H
* If it is difficult to remove, hold the bottom of
the inside base
(if there are cat litter inside, hold the the
base from the top of the litter) with one
hand, and hold the lock with the other hand
to raise the hood.
Place the hood on the base.
①
Hold under the hole on the base using one hand.
②
Then, use other hand to open the lock part on the hood to
lower. Do the same step on other side to attach the hood.
③
Lift the hood and make sure it does not come off.
* If it comes off, check the lock part from above and make
sure the protrusion part is inside the hole. (See how the
lock looks)
Hood
Base
Lock
Cats, who do not like dirty areas, prefer to use a clean bathroom.
Please make sure to keep it clean all the time.
l
Please use clumping cat litter that is available at store.
For the amount of cat litter usage, please follow the instruction manual for cat litter.
l
Remove the hood when changing the cat litter.
* The scoop can be stored in the hood.
l
Use a mild detergent and water to clean. After cleaning,
dry in the shaded and well-ventilated place.
803840 600252 / 803840 600269 / 803840 600276
The view of
lock part
Gap
Gap
No Gap
Protrusion part
Protrusion part
Hole
Designed by:
Richell Corporation, Japan
Distributed by:
Richell USA, Inc.
Grand Prairie, Texas 75050
Phone (972) 641-9795 Fax (972) 641-8495
Visit us at
www.richellusa.com
MADE IN JAPAN