background image

INSTALLATION INSTRUCTIONS 

MODELS RXRD-NDCM3 & RXRD-NFCM3

HORIZONTAL AIRFLOW ECONOMIZERS

WARN ING

THIS ACCESSORY IS TO BE INSTALLED BY A QUALIFIED, LICENSED SERVICE PERSON. TO AVOID

UNSATISFACTORY OPERATION OR DAMAGE TO THE PRODUCT AND POSSIBLE UNSAFE CONDITIONS,

INCLUDING ELECTRICAL SHOCK, REFRIGERANT LEAKAGE AND FIRE, THE INSTALLATION

INSTRUCTIONS PROVIDED WITH THIS ACCESSORY MUST BE STRICTLY FOLLOWED AND THE PARTS

SUPPLIED USED WITHOUT SUBSTITUTION. DAMAGE TO THE PRODUCT RESULTING FROM NOT

FOLLOWING THE INSTRUCTIONS OR USING UNAUTHORIZED PARTS MAY BE EXCLUDED FROM THE

MANUFACTURER’S WARRANTY COVERAGE.

DISCONNECT ELECTRICAL POWER TO THE UNIT. FAILURE TO DO SO CAN CAUSE ELECTRICAL SHOCK

RESULTING IN PERSONAL INJURY OR DEATH.

WARN ING

TOOLS  RE QUIRED  FOR  IN STAL LA TION:

3

8

" elec tric drill with 

5

16

" socket

Small flat blade (0.125" wide) screw driver

Wa ter proof  ex te rior  duct  seal ant

Sheet metal tools (e.g. shears)

PACK AGE  CON TENTS

RXRD-NDCM3

economizer with

controller, actuator,

and outside enthalpy

sensor attached

RXRD-NFCM3

economizer with

controller, actuator, and
outside enthalpy sensor

attached

ITEM

DE SCRIP TION

PART No.

PART No.

1

Discharge Air Sensor (Hardware Bag)

6039413 / 3112

6039415 / 3112

2

(2) Permanent Filters

6039413 / 8567

(11.875" X 23.875")

6039415 / 8568

(23.875" X 23.875")

3

(2) Spotweld Assy - Bird Screen

6039413 / BSWA

6039415 / BSWA

4

(2) Exhaust Air Rainhood - Top 

6039413 / EHT2

6039415 / EHT2

5

OA Rainhood Assy - Left Side

6039413 / EHSL

6039415 / EHSL

6

OA Rainhood Assy - Right Side

6039413 / EHSR

6039415 / EHSR

7

(2) Exhaust Air Rainhood - Left Side

6039413 / EHS3L

6039415 / EHS3L

8

(2) Exhaust Air Rainhood – Right Side

6039413 / EHS3R

6039415 / EHS3R

9

OA Rainhood Assy - Filter Bracket Strip

6039413 / ADP

6039415 / ADP

10

OA Rainhood Assy – Top

6039413 / EHT

6039415 / EHT

11

OA Rainhood - Front Filter Support

6039413 / EHB

6039415 / EHB

12

OA Filter Rail

6039413 / FCH

6039415 / FCH

13

Hardware Bag

6039413 / HDW

6039415 / HDW

TABLE 1

Summary of Contents for RXRD-NDCM3













Reviews: