background image

1

ENGLISH

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may 

not cause harmful interference, and (2) this device must accept any interference received, including interference that may 

cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the 

FCC Rules. These limits are designed to this equipment generates, uses, and can radiate radio frequency energy and, if not 

installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, 

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful 

interference to radio or television reception, which can be determined by turning the radio or television off and on, the user 

is encouraged to try to correct interference by one or more of the following measures: 
•  Reorient or relocate the receiving antenna. 
•  Increase the separation between the equipment and receiver. 
•  Connect the equipment into an outlet on another circuit. 
•  Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s 

authority to operate this equipment.

Industry Canada Regulatory Information

CAN ICES-3 (B)/NMB-3 (B)

Avis d’Industrie Canada

CAN ICES-3 (B)/NMB-3 (B)

Important:

 This power adapter should be plugged in so that it stays vertical or lays flat.

ANT702F

Digital Amplifi ed Indoor/Outdoor Antenna

User’s Guide

Getting Started 

Remove the antenna and the hardware bag from package. Make sure the 
following parts are in the package:

•  Antenna
•  Amplifi er Insert   

•   Power Adapter 

•   Mounting Base    

•   Mounting Arm

•  Hardware bag: 

(2) U-Bolts

(2) Clamps

(4) Plastic Anchors

(4) Wood screws

(4) Washer Nuts       

(1) Coaxial cable

(2) Bolts

BEFORE YOU START!!!

Please read the IMPORTANT SAFETY INFORMATION sheet included in 
this package.

ENGLISH

Summary of Contents for ANT702F












Reviews: